This is a fairly non-specific steerable nose wheel strut for RC aircraft. It's is 2.3" from top to the center of the nose wheel axle.
It is designed for a 5-10 size retract (20-30oz airplane) and has an integrated Steering arm. The axle is size for a M3, the steering arm is size for M2 and the retract shaft hole is size for M4. You can drill it out for plain old 1/8" too. The wheel cut out is sized for a 1 1/2" wheel. Smaller wheels will work too.

This is a servo mount for a micro servo. This allows you to mount a servo on it's side without having to glue it in. You can then easily remove the servo if need be.

This is a generic mount block for two micro servos side-by-side. It's really designed to be glued down onto a flat surface, but I have make a couple of small (1/16") holes so you can screw it down. It's designed to allow the servos to be inserted from the side so you don't damage the wires

Customized version of thingiverse.com/thing:47956

Created with Customizer! thingiverse.com/apps/customizer/run?thing_id=47956

This is the counter-rotating version of my 2.5in 3 blade spinner (http://www.thingiverse.com/thing:44872). The negative offset base is unchanged from the normal rotating spinner. I uploaded it again for convenience.

It is designed for a 8" or 9" x 6-7" 3 bladed counter rotating prop.

This is another spinner. This just a bit under 2.5" diam (2.4375" to be exact). It is designed for a 9" x 6-7" 3 bladed prop.

This is an attachment so you can use your iPhone 4s and the Clinometer app plaincode.com/products/clinometer/ as a RC heli rotor blade pitch gauge.

This is a tail servo mount for a 450 Pro where the tail servo is mounted to the carbon fiber frame halves

Tail boom support assembly for a Century Swift NX 550 RC Heli

This is an alternate ESC/BEC mounting plate for a Century Swift NX 550 electric heli. It's made specifically for a HobbyWing 80A HW ESC. The HobbyWing ESC won't fit in the normal place for the ESC and there isn't a clean way to attach it. This provides for bolting the ESC to the Heli with real screws and captive hex nuts. It has a pretty big space for BEC so you can use what ever you want.

This is a two piece spinner for a Howard DGA-3 Pete RC airplane. Thought it will work on any 200w range motor with a .25in shaft diameter prop adapter. It's designed around a Master Airscrew 6x4 prop. It's held together by two M3x8mm socket head cap screws.

I am planning on fiddling with the thickness to get the weight down. I will also play with cooling holes. Stay tuned.

This is a mounting block for attaching an Align or Align clone MD500 fuselage to a T-Rex 450 or 450 clone RC heli. It's quite a bit stronger than the laser cut plywood that typically comes with the fuselage kit

This is a two blade version of the 3in spinner I uploaded a while ago.

This is a two bladed version of the 3in spinner I uploaded a while ago.

This is the base plate for the 3in RC Plane Spinner.

1.75in diam x 2.5in tall spinner for a Master Air Screw 6x4 3 blade prop. The base has a "fan" in the skirt to help with cooling. This was made for a Hobby King 750mm GB R3 but can be used for whatever.It's designed for a 5mm prop adapter main shaft.

This is a two piece propeller spinner. It's 3in in diameter and has a 5mm shaft hole. It's pretty light compared to commonly available molded plastic ones. I have on installed on a 32 size motor and have dozens of flights. No issues.

I downloaded and printed out AlexEnglish's slug trap and though I would try my hand at a design. I haven't printed it out yet, so it's a work in progress. If you print it out, let me know if there are any issues. I pretty much maxed out the Replicator print volume.