MendelMax Power (IEC, fuse, switch) and USB panel
14
Likes
264
Downloads
1383
Views
Published on July 24, 2012
Description
A panel for the MendelMax to hold a USB socket, IEC power socket, fuse, and switch.
Has optional text too.
Work in progress because I haven't gotten my USB sockets yet to verify the dimensions. Should be re-printed and installed in a few days.
UPDATE: I removed some of the text since it wasn't printing well. All text can be turned of with one simple change in the .scad. I added the corner cutouts on the IEC connector, and updated the dimensions. I printed a first draft but am still waiting for the USB socket.
UPDATE 2: I made some small adjustments after getting the USB jack. New scad and stl are posted. the actuall diff is in a comment below.
Has optional text too.
Work in progress because I haven't gotten my USB sockets yet to verify the dimensions. Should be re-printed and installed in a few days.
UPDATE: I removed some of the text since it wasn't printing well. All text can be turned of with one simple change in the .scad. I added the corner cutouts on the IEC connector, and updated the dimensions. I printed a first draft but am still waiting for the USB socket.
UPDATE 2: I made some small adjustments after getting the USB jack. New scad and stl are posted. the actuall diff is in a comment below.
Instructions
Print this.
Get these:
StarTech 1-Feet Panel Mount USB Cable B to B - F/M (USBPNLBFBM1)
amazon.com/gp/product/B002M8VBIS/ref=oh_details_o02_s00_i00
3 Pin IEC320 C14 Inlet Male Power Socket w Fuse Switch 10A 250V
amazon.com/IEC320-Inlet-Power-Socket-Switch/dp/B00511QVVK
uxcell.com/pin-iec320-c14-inlet-male-power-socket-fuse-switch-10a-250v-p-104813.html
If you want to change the scad, you'll need a font (one file from thing #13677), and you'll have to set some paths internally (not hard).
If you put your panel near the motor pulley, I would recommend a guard, like this one: thingiverse.com/thing:27420
Get these:
StarTech 1-Feet Panel Mount USB Cable B to B - F/M (USBPNLBFBM1)
amazon.com/gp/product/B002M8VBIS/ref=oh_details_o02_s00_i00
3 Pin IEC320 C14 Inlet Male Power Socket w Fuse Switch 10A 250V
amazon.com/IEC320-Inlet-Power-Socket-Switch/dp/B00511QVVK
uxcell.com/pin-iec320-c14-inlet-male-power-socket-fuse-switch-10a-250v-p-104813.html
If you want to change the scad, you'll need a font (one file from thing #13677), and you'll have to set some paths internally (not hard).
If you put your panel near the motor pulley, I would recommend a guard, like this one: thingiverse.com/thing:27420
You must be logged in to post a comment.
zerocool5878
on
August 12, 2012
said:
Just wondering if you received your USB cord yet. I was thinking about printing this out tonight. Just ordered the bits from amazon
zerocool5878
on
July 25, 2012
said:
I think im going to add this to my build. Should have a pic in a week or so Thanks for this :)
mfinn
on
August 12, 2012
said:
I did, Here were the changes:
&
lt; usb_flange_height=16; //indent in back for usb molding
&
gt; usb_flange_height=14.5+1; //indent in back for usb molding
&
lt; usb_flange_width=34; //indent in back for usb molding
&
gt; usb_flange_width=39+1; //indent in back for usb molding
&
lt; usb_flange_thick=2.5; //thinckness of plate over USB molding
&
gt; usb_flange_thick=2.25; //thinckness of plate over USB molding
I'll post a new stl and scad in a few minutes
License
MendelMax Power (IEC, fuse, switch) and USB panel by mfinn is licensed under the Attribution - Non-Commercial - Share Alike license.
More from mfinn
More from 3D Printer Parts
Mfinn, thanks for this. Could you post the version without any text at all please? thank you in advance.