Loading

Orca 0.4x Hotend cooling ring

by Okatake, published

Orca 0.4x Hotend cooling ring by Okatake Oct 17, 2012

Description

Cooling ring for cooling the hot end. ※: possible distance to the bottom end of the hot (thermal core) is attached to the case of 47.5mm

Recent Comments

view all
Success! Cheers!
Hi paoel.

Appears normally tried by "Repetier-Host V0.74".I've tried the steps listed below.

1.(Repetier-Host):"Repetier-Host V0.74"→"Slicer"→"Slic3r(Configure)"2.(Slic3r):"File"→"Load Config"→[CoolingRing_v10_3.ini]2.(Slic3r):"Plater"→"Add"→[CoolingRing_v10_3.stl]3.(Slic3r):"Export G-code"→SAVE G-code→Close Slic3r4.(Repetier-Host):"File"→"Load G-code"→File name of the No.3

Thank you.
Hi there, thanks for the quick reply. Unfortunately no luck. 

Slic3r is giving the error that the model contains intersecting facets.

See the print screen using your settings:

dl.dropbox.com/u/2307778/slic3r_error.png

More from 3D Printer Accessories

view more

Liked By

view all

Tags

Give a Shout Out

If you print this Thing and display it in public proudly give attribution by printing and displaying this tag. Print Thing Tag

Instructions

Must be removed after printing because the STL with the print material support.

**Parts need 30mm fan × 1 M3-15mm bolt × 4 M3 washer × 4 M3 nut × 4 M4-35mm bolt × 5 M4-30mm bolt × 1

I generated the G-Code using the "slic3r 0.9.3".

The main thing is that when the following parameters. Layer hight 0.25mm Infill 100% Perimeters 25mm / s Small perimeters 15mm / s External perimeters 80% Infill 45mm / s Solid infill 45mm / s Top solid infill 20mm / s Bridges 45mm / s Support material Overhang threshole 10 degrees Pattren rectilinear Pattern spacing 2.5mm Pattern angle 90 degrees

Hi there, I'm using your settings, but slic3r seems to have problems creating the bottom part (around the nozzle) it's not there at all.

Any suggestions?
Hi paoel.

Please refer to the ini file I uploaded "Slic3r" was used to generate the G-Code.

I think if the support material is an issue that remains inside the nozzle, and may be removed by hand things remaining in the set to three degrees the angle of the "Support material Overhang threshole".

Please print it and modify it as needed is a reference value set.
Hi there, thanks for the quick reply. Unfortunately no luck. 

Slic3r is giving the error that the model contains intersecting facets.

See the print screen using your settings:

dl.dropbox.com/u/2307778/slic3r_error.png
Hi paoel.

Appears normally tried by "Repetier-Host V0.74".I've tried the steps listed below.

1.(Repetier-Host):"Repetier-Host V0.74"→"Slicer"→"Slic3r(Configure)"2.(Slic3r):"File"→"Load Config"→[CoolingRing_v10_3.ini]2.(Slic3r):"Plater"→"Add"→[CoolingRing_v10_3.stl]3.(Slic3r):"Export G-code"→SAVE G-code→Close Slic3r4.(Repetier-Host):"File"→"Load G-code"→File name of the No.3

Thank you.
Success! Cheers!
Top