Clicky

Loading

Report as inappropriate

THIS PAGE IS NO LONGER UPDATED

FOR CONVENIENCE PURPOSES I MADE THIS A DESIGN WHICH IS EDITED FREQUENTLY

https://www.thingiverse.com/thing:3574369

So I have been all over the group lately, trying to assist here and there the best I can. I am no Ender 3 expert, or 3d printing as a whole. But I do have a great grasp on the concept of printing, from failures and success of my own. So I created this here to give people a one stop shop for assistance. All information can also be found if you know who to look for them, but this is for those who just cannot seem to locate the info they need or are too lazy to do the legwork themselves. In the end the goal is to same, get it working and getting answer

This is where it all began had to make it into a thingi because I change and change and change things so much they flagged the post, sucks because I have it pinned in the ender3 group, but this is the origin page of this beauty https://www.thingiverse.com/groups/ender3/forums/general/topic:36068#comment-2455385


Change log
4/25/2019
Added under extrusion issue that I, the OP for this guide, experienced.

4/22/2019
Rearranged some thing in the text. Kinda threw everything together as it was found or provided to me. Just basically made it easier to read through. So structural and literacy edits, nothing more

Added Fixes:
User @TheMagicalC added a great suggestion regarding belt tension. Which I had done myself as well, but did not think much of it as it was sensible for me to do some might now think so simply as I and TheMagicalC had done. See "user fixes" section below

04/20/2019
Added Reddit Link for Fixes, upgrade fixes, and common issues


Got bored and looked around on facebook at the official Ender 3 group, and found something, IMO, that many of you could/ should take a look at this as well.**
Enjoy the loooooooong read. (see attached PDF)
**Full disclosure TL/DR

So I thought I would add a pretty good assembly video, which I followed and have had none of the common little issues. This along with some of the other links below have help me and others. So check it out if you haven't yet. https://youtu.be/me8Qrwh907Q

Reddit link for Recommended fixes and upgrades
https://www.reddit.com/r/3Dprinting/wiki/newguideender3

Another great reference regarding printer alignment which many of you find useful
https://www.youtube.com/watch?v=xnzNd_FIMKY

Another guide for assembly from makersteve, just a different approach with a few different steps
https://makersteve.com/2018/08/25/ultimate-build-guide-for-creality-ender-3-step-by-step-a-makersteve-special-report/

FOR THOSE WITH Z AXIS BINDING ISSUES / makersteve
https://makersteve.com/2018/08/24/ender-3-z-axis-binding-fix-bring-a-basic-stringing-test/

FOR THOSE WITH COMPRESSION/ PUSH FITTING ISSUES OR JUST LOOKING TO SAY TO CHANGE THEM FROM STOCK / makersteve
https://makersteve.com/2019/01/04/a-tale-of-eight-enders-maker-steves-bowden-edition-compression-fitting-fix/

EXTRUDER UPGRADE AND POSSIBLE UNDER EXTRUSION FIX / makersteve
https://makersteve.com/2019/03/19/a-tale-of-eight-enders-aluminum-extruder-upgrade

Another guide, this one is regarding the XT-60 connectors which connect from the PSU to the Control boards main PWR / makersteve
https://makersteve.com/2019/04/16/safety-first-replace-those-bad-xt60-connectors-ender-3-fix/

Next link is not a troubleshooting link but is still good to have the ENDER 3 Github info
https://github.com/Creality3DPrinting/Ender-3

REPRAP IS YOUR FRIEND, GET FAMILIAR WITH IT

TROUBLESHOOTING LINKS LISTED BELOW
Generic Troubleshooting - https://reprap.org/wiki/Troubleshooting
Print Specific Troubleshooting -
https://reprap.org/wiki/Print_Troubleshooting_Pictorial_Guide
Extrusion Issues - https://reprap.org/wiki/Inconsistent_Extrusion_Troubleshooting_Guide
Calibration Fun - https://reprap.org/wiki/Calibration
Heated Bed https://reprap.org/wiki/Heated_Bed


USER FIXES COMMON AND UNCOMMON

USER: TheMagicalC
"The Pry and Tighten"
Something I'd like you to add to help others (as I experienced this problem) is that if your prints come out oblong or sort of stretched along a diagonal, it means your X-Axis belt needs tightening. If you have difficulty tightening it with your hands, you can put an allen wrench between the roller at the end of the x-axis bar and the bar itself and lever the roller farther out with the allen wrench, and tighten the screws with a different wrench once it reaches optimal tightness. It should twang a little bit if you pluck it. Thanks for your work helping the Ender 3 community.

USER: BoothyBoothy
"Toe The Line"
X Axis Drive Belt Not Parallel to Extrusion
I had an issue on my Ender 3 Pro where the X Axis drive belt was not running parallel to the extrusion. After a lot of investigation in turned out that the tensioner assembly plate was slightly bent. Using a shim between the plate and the extrusion rectified this issue (see attached images from original message on this thingi and also on the original post)****

USER: Ender3Guy
"The Straight and Narrow"
Personally I probably had one of the worst Enders ever sold. I spent months trying to figure out why the bed wouldn't level when it was already flat. The front right and rear left corners were perpetually too high Finally, DerWaldschrat (I think that's how you spell his username) pointed out that it had to be a warped Y axis extrusion. Sure enough, it leveled perfectly after replacing the extrusion.

USER: SHENKOE (wait thats me)
"The Rub-A-DubDub"
Ohhh Nooooo (in my Family Guy voice) I have under extrusion. Why could this be happening I just printed something and switched out filament, now it under extrudes.
ender 3 (obviously)
Micro Swiss All Metal Hotend w/ 0.4mm standard steel nozzle
Hatchbox, Esun, and CC3D for PLA / Sunlu for PLA+
capricorn xs ptfe
stock extruder with 3rd party push fittings

So I checked the nozzle clear, did cold/ atomic pulls with white filament to be sure all was clean. tightened the nozzle, removed the nozzle, removed the heat break from the sink and checked interior walls, all clean,checked tube seems good, a little worn from use on 2 printers, but still good. checked extruder assemble, there is tension, but there could be more.
Tested first layer everytime I completed a step, everytime it would under extrude. So I decided to swap the ptfe tube for one I had not used from some other 3rd party. Removed the extruder release arm, low and behold the filament had already worn a groove in the arm after only a few weeks of moderate printing. Luckily I believe in spare parts and had printed an extruder assembly called the Bantamfeeder > https://bantam.design/feeder 2 weeks ago, unsure when I would test it. Well guess im testing it out now.

So I swapped out the assembly and ptfe tube, viola issue resolved see newly added photos.


So I found this while shredding some waves. Just tips to help people address their issues in the forum and how to get answers sooner, rather than later or not at all. These are not oriented towards 3d printing, but the intent still applies to any forum that you request help on.

Before You Ask

Before asking a technical question by email, or in a newsgroup, or on a Web site chat board, do the following:

Try to find an answer by searching the Web.

Try to find an answer by reading the manual.

Try to find an answer by reading a FAQ.

Try to find an answer by inspection or experimentation.

Try to find an answer by asking a skilled friend.

When You Ask

Choose your forum carefully

Be sensitive in choosing where you ask your question. You're likely to be ignored, or written off as a loser, if you:

Post your question to a forum where it's off topic

Post a very elementary question to a forum where advanced technical questions are expected, or vice-versa

Cross-post to too many different newsgroups

Post a personal e-mail to somebody who is neither a personal acquaintance nor personally responsible for solving your problem

Use meaningful, specific subject headers

On mailing lists, newsgroups, or Web forums, the subject header is your golden opportunity to attract qualified experts' attention, in around 50 characters or fewer. Don't waste it on babble like "Please help me" (let alone "PLEASE HELP ME!!!!"; messages with such subjects get discarded, by reflex). Don't try to impress us with the depth of your anguish; use the space for a super-concise problem description, instead.

One good convention for subject headers, used by many tech support organizations, is "object - deviation". The "object" part specifies what thing, or group of things, is having a problem. The "deviation" part describes observed deviation from expected behaviour.

(non-3d printing question examples)
Stupid:
HELP! Video doesn't work properly on my laptop!

Smart:
X.org 6.8.1 misshapen mouse cursor, Fooware MV1005 vid. chipset

Smarter:
X.org 6.8.1 mouse cursor on Fooware MV1005 vid. chipset - is misshapen

Be precise and informative about your problem

Describe the symptoms of your problem or bug carefully and clearly.

Describe the environment in which it occurs (machine, OS, application, whatever). Provide your vendor's distribution and release level (e.g.: "Fedora Core 2", "Slackware 9.1" etc.).

Describe the research you did to try and understand the problem before you asked the question.

Describe the diagnostic steps you took to try and pin down the problem yourself, before you asked the question.

Describe any possibly relevant recent changes to your computer or software configuration.

Ok this became longer than I wanted, so if this is unclear, check the link out


I recommend this to anyone who has had or has issues with the bed getting leveled or is just plain tired for leveling at anytime. I personally do not believe in ABL devices, they are band-aids to the actual issue. If you haven't heard of it or just have not cared to do this next step you should. *https://www.thingiverse.com/thing:3415460 and pair it with this to complete the conversion https://www.thingiverse.com/thing:3193722.**

After these changes were made on my ender 3s or my other printer formerly known as an A8(still have just not used and halfway disassembled), I have what I like to call walk away printers. I press print and walk away, without fear of a bad first layer. Check on the printer after a few minutes, if I'm still around, and if all looks good (whether still on the first layer or not) I let it rockout.

the second link is specifically for the Ender 3. I have done this on both my E3's, I use double thumbwheels with nyloc nuts and no springs.

SPRINGS ARE BAD, MMMMKAAAY.

IF YOU CHOOSE TO DO THESE CHANGES YOU DO SO AT YOUR OWN RISK, AS I HAVE HAD ONLY POSITIVE RESULTS WITH THIS SETUP ON 3 DIFFERENT PRINTERS. YOUR OWN EXPERIENCE MAY VARY

NOT MY STL MODEL OF THE ENDER 3 JUST ADDED IT TO GET THIS POSTED (LINK TO PERSONS WHO CREATED THE STL FILE- https://www.tinkercad.com/things/4WGWB2OmqR4-creality-ender-3-model

ENDER 3/ Ender 3 Pro/ Ender 3X TROUBLESHOOTING GUIDE AND HOW TO REQUEST HELP
by SHENKOE
Hot Bed Leveling and 3-Point Mounting
Simple Ender 3 mod for 3-point tramming
by rrwrex