General information collated into the most often asked questions and answers. NOT an official Anycubic-operated forum; just customers discussing their machines.
FIRMWAREhttps://www.thingiverse.com/groups/anycubic-i3-mega/topic:16543
HARDWAREhttps://www.thingiverse.com/groups/anycubic-i3-mega/topic:26118
Print Bed Flatnesshttps://www.thingiverse.com/groups/anycubic-i3-mega/topic:18001
Manual Leveling ANYCUBIC i3 MEGAhttps://www.youtube.com/watch?v=6QhUgq4C008
Resume after power losshttps://www.thingiverse.com/asset:50112
PETGhttps://www.thingiverse.com/groups/anycubic-i3-mega/topic:17664
PLAhttps://www.matterhackers.com/articles/how-to-succeed-when-printing-in-pla
Print Quality Troubleshootinghttp://reprap.org/wiki/Print_Troubleshooting_Pictorial_Guidehttps://www.simplify3d.com/support/print-quality-troubleshooting
Official Anycubic websitehttp://www.anycubic3d.com/index.htmlhttp://www.anycubic.cn/en/
X and Y "belt bearings" (pulleys):
GT2 idler pulley (20 teeth) 5mm bore for 6mm belt
People really need to give more information on their settings and filaments with their questions. and pictures help too.
Cura printhead settings for the i3 Mega x=210 y=210 z=205 This applies to any slicer that wants to know how big the bed/printspace is.
Gcode flavour: Marlin/Reprap
Great logic to have all i3 mega at a single drill down index
General information collated into the most often asked questions and answers.
NOT an official Anycubic-operated forum; just customers discussing their machines.
FIRMWARE
https://www.thingiverse.com/groups/anycubic-i3-mega/topic:16543
HARDWARE
https://www.thingiverse.com/groups/anycubic-i3-mega/topic:26118
Print Bed Flatness
https://www.thingiverse.com/groups/anycubic-i3-mega/topic:18001
https://www.thingiverse.com/groups/anycubic-i3-mega/topic:18757
related:
Manual Leveling ANYCUBIC i3 MEGA
https://www.youtube.com/watch?v=6QhUgq4C008
Resume after power loss
https://www.thingiverse.com/asset:50112
PETG
https://www.thingiverse.com/groups/anycubic-i3-mega/topic:17664
PLA
https://www.matterhackers.com/articles/how-to-succeed-when-printing-in-pla
Print Quality Troubleshooting
http://reprap.org/wiki/Print_Troubleshooting_Pictorial_Guide
https://www.simplify3d.com/support/print-quality-troubleshooting
http://www.desiquintans.com/coolingtests
http://www.desiquintans.com/coolingtests2
Official Anycubic website
http://www.anycubic3d.com/index.html
http://www.anycubic.cn/en/
http://www.anycubic3d.com/aftermarket.html
https://www.thingiverse.com/enry68/collections/mega
https://www.thingiverse.com/lunadaniel/collections/anycubic-i3-mega
https://www.thingiverse.com/AJK50/collections/anycubic-i3-mega
X and Y "belt bearings" (pulleys):
GT2 idler pulley (20 teeth) 5mm bore for 6mm belt
People really need to give more information on their settings and filaments with their questions. and pictures help too.
Cura printhead settings for the i3 Mega
x=210
y=210
z=205
This applies to any slicer that wants to know how big the bed/printspace is.
Gcode flavour:
Marlin/Reprap
Great logic to have all i3 mega at a single drill down index