Loading

Recent Topics

My Auto Shutdown Solution

by dlsmith57918

I do a lot of printing that ends up finishing the job in the wee hours of the morning, and wanted to have a way the printer would shut down after finishing the print. Browsing the Duet3D Gcode rference, I found that codes M80 and M81 control the external PS port, and that by using that signal abd a couple of relays and a small 5 volt power supply I could get the printer to shut down automatically.
I used a 5 volt relay board, with the input connected to the PS_ON pin and the ground connected to the GND pin. The 5 volt power supply supplies 5 volts to the relay board. The jumper on the relay board is set to trigger when the PS_ON pin goes low.
I used an adjustable delay board to power the printer up until the PS_ON signal goes high and activates the signal relay.
The line (L - hot) power wire is connected to the 5 volt power supply and the common poles on both relays. The NC (normally closed ) relay terminal on the delay relay and the NO (normally open) relay terminal on the signal relay are then connected to the line (L) terminal on the printer PSU. The neutral power line is connected to the neutral (N) terminal on the 5 volt power supply and the neutral (N) terminal on the printer PSU.
I set the delay relay to remain closed for 5 seconds, and then open, as the signal relay will have closed and sent line current to the NO terminal and on to the printer PSU.
You will need to put an M80 command in the config.g file on the SD card so the PS_ON pin goes high, otherwise, after the delay relay opens, the printer will shut down again.
To shut the printer down after finishing a print, simply put an M81 S1 command either at the end of the gcode file or in S3D in the ending script. The S1 parameter delays the shutdown until all cooling fans have turned off, letting the hot end cool off properly.
The 5 volt power supply remains powered up to keep the delay relay from sending power to the printer PSU. You will need to cut the power and then reapply power to get the printer to power up again, unless you install the optional override switch.
I have my printer in the basement, so I have it plugged into a remote control power socket, so I can power it up or down from my desk.

Attached are a circuit diagram, pictures of the finished unit and the stl files for the case and lid.

Link to delay module: https://www.amazon.com/gp/product/B07H5D3R3M/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1

Link to signal relay: https://www.amazon.com/gp/product/B07QGT6RGX/ref=ppx_yo_dt_b_asin_title_o05_s01?ie=UTF8&psc=1

Link to 5 volt power supply: https://www.amazon.com/gp/product/B07CBS768L/ref=ppx_yo_dt_b_asin_title_o07_s01?ie=UTF8&psc=1

Link to fused power cord receptacle: https://www.amazon.com/gp/product/B082ZFRV1B/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1

Auto shutoff Duet Hypercube
View Comment

Cura start Gcode

by X301N

I've read somewhere in the duet forum that you need to tell the board in the start gcode that the movements are not relative.
Is it still needed?

View Comment

Dual Z stepper problem

by dlsmith57918

I have a dual stepper Z axis setup on a Hypercube driven by a Duet Ethernet board. The only problem I have with it is after finishing a print, I have a script in Simplifiy3D that lowers the build platform and homes the X and Y axes. Every time it does this, if I home the Z axis, the right side is a few mm higher and the build plate hits the extruder nozzle when it raises to the home position. I can manually turn the actuator rod a few steps and lower that side back to the correct position, but I can't understand why it does this. The platform isn't binding as I have taken it loose from the follower nuts and it slides up and down the entire range of travel freely.
Now if it use the Panel Duet and manually move the platform up and down, even over the full 300mm range, it never gets out of alignment.

Any ideas what might be going on?

View Comment

Setup-firmware

by Renfeld

Can anyone help me do the firmware for my duet2 wifi? I've been reading, but I'm more confused now that I was before. I'm using it to replace the trigorilla board from my anycubic chiron. Any help would be appreciated.

View Comment

Sending G-Code via the USB COM Port using Python

by Decarnifex

Hello there!
I want to talk to my Duet2Wifi via USB COM. I know there's YAT and it's working pretty well. But I need to seperate my G-Code after the slicing process to send it to my board (because I use a special kind of printer). I could use Wifi but I'm worried about the higher latency. So I chose Python for the communication. Using PySerial and PyUSB (modifying the Duet driver through the libusb library), I can't get the board to answer my commands. I provided both source codes down below. Does anyone have some ideas?

View Comment