Loading

Lulzbot Mini profiles for Simplify3D

Please Login to Comment

Does anyone have a good .FFF for the Lulzbot Mini? I'm a bit disappointed in the quality of prints from Simplify3D. I'm working to correct the problems as I go, but I'm new at this and would like a good jumping off point if anyone has a great .FFF they would share.

Thanks.

<?xml version="1.0"?>

LulzBot Mini ABS Medium 0 0.5 1 0.6 1 1 1.5 0 0.1 900 0 0.1 0 2.5 0 0.2501 4 3 2 1 2 0 0 300 0 0 150 110 0.3 0 0 3 3 0.14 85 0 1 0 1 2 3 0 999 12 7 1 0 999 2 1 1 30 1 0 Rectilinear Rectilinear 20 25 180 2 1 45,-45 0 0 0 30 0 0 70 1 0.3 1 1 0 4 45 0 0 0 0 0 1 0 1 0 0 1 1 1 15 20 1 15 60 1 70 1 0 1 0 0 1 0 0 0 0 1 0 152 152 158 0 0 0 -1 -1 1 1 -1 1 0,0|0,0|0,0|0,0|0,0|0,0 1 RepRap (Marlin/Repetier/Sprinter) r2 115200 0 G21 ; metric values,G90 ; absolute positioning,M82 ; set extruder to absolute mode,M107 ; start with the fan off,G92 E0 ; set extruder position to 0,M140 S[bed0_temperature] ; begin bed heating,G28 ; home all,M109 S150 ; set and wait for RETRACT TEMP (ABS=150),G1 Z150 E-30 F75 ; suck up 30mm of filament,M109 S170 ; set and wait for CLEANING TEMP (ABS=170),G1 X45 Y174 F11520 ; move nozzle over wiper pad,G1 Z0 F1200 ; CRITICAL: set Z top of pad,G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad,G1 X55 Y172 Z-.5 F4000 ; wiping,G1 X45 Y174 Z0 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X90 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury nozzle in cleanish area,G1 Z10 ; raise z,G28 X0 Y0 ; home x and y,M109 S170 ; set to PROBING TEMP (ABS=170),M204 S300 ; set accel for probing,G29 ; Probe,M204 S2000 ; set accel back to normal,G1 X5 Y15 Z10 F5000 ; get out the way,M400 ; clear buffer,G4 S1 ; pause,M140 S[bed0_temperature] ; Set bed temp again,M109 S[extruder0_temperature] ; set extruder temp and wait,M190 S[bed0_temperature] ; wait for bed to finish heating if needed,G1 Z2 E0 F75 ; extrude filament back into nozzle,G1 Z2 E5 F75 ; extrude a blob to prime nozzle (sw),G1 Z2 E4.5 F600 ; retract 0.5mm (sw),G1 X15 Y15 Z10 F5000 ;move away from blob so S3D doesn't plunge into it (sw),G92 E0 ; reset extruder position to 0 (sw), M400 ; wait for operations to complete,M104 S0 ; hotend off,M140 S0 ; bed heater off ,M107 ; fans off,G92 E3 ; set extruder to 3 (will cause -3 retraction in next command),G1 X90 Y5 Z159 E0 F5000 ; move to cooling position and retract filament to relieve pressure,M190 R50 ; Set and wait for PEI BED REMOVAL TEMP (ABS=50),G1 Y175 F1000 ; move to cooled position,M84 ; steppers off,G90 ; absolute positioning,G4 S7200 ; hold bed temp for 2 hours (s=time in seconds),M140 S0 ; bed heater off, 0 0 Random Song 0 3000 0.75 0.75 0.8 10500 480 50 0 1 1 2.87 43 1.04 0 0 0 0 0 20 0 0 1 0 1 1.5 1 1 0 3 0 0 600 1 10 0 110 0.3 240 100 1 15 20 1 15 60 1 70 3000 2.87 43 1.04 G21 ; metric values,G90 ; absolute positioning,M82 ; set extruder to absolute mode,M107 ; start with the fan off,G92 E0 ; set extruder position to 0,M140 S[bed0_temperature] ; begin bed heating,G28 ; home all,M109 S150 ; set and wait for RETRACT TEMP (ABS=150),G1 Z150 E-30 F75 ; suck up 30mm of filament,M109 S170 ; set and wait for CLEANING TEMP (ABS=170),G1 X45 Y174 F11520 ; move nozzle over wiper pad,G1 Z0 F1200 ; CRITICAL: set Z top of pad,G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad,G1 X55 Y172 Z-.5 F4000 ; wiping,G1 X45 Y174 Z0 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X90 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury nozzle in cleanish area,G1 Z10 ; raise z,G28 X0 Y0 ; home x and y,M109 S170 ; set to PROBING TEMP (ABS=170),M204 S300 ; set accel for probing,G29 ; Probe,M204 S2000 ; set accel back to normal,G1 X5 Y15 Z10 F5000 ; get out the way,M400 ; clear buffer,G4 S1 ; pause,M140 S[bed0_temperature] ; Set bed temp again,M109 S[extruder0_temperature] ; set extruder temp and wait,M190 S[bed0_temperature] ; wait for bed to finish heating if needed,G1 Z2 E0 F75 ; extrude filament back into nozzle,G1 Z2 E5 F75 ; extrude a blob to prime nozzle (sw),G1 Z2 E4.5 F600 ; retract 0.5mm (sw),G1 X15 Y15 Z10 F5000 ;move away from blob so S3D doesn't plunge into it (sw),G92 E0 ; reset extruder position to 0 (sw), M400 ; wait for operations to complete,M104 S0 ; hotend off,M140 S0 ; bed heater off ,M107 ; fans off,G92 E3 ; set extruder to 3 (will cause -3 retraction in next command),G1 X90 Y5 Z159 E0 F5000 ; move to cooling position and retract filament to relieve pressure,M190 R50 ; Set and wait for PEI BED REMOVAL TEMP (ABS=50),G1 Y175 F1000 ; move to cooled position,M84 ; steppers off,G90 ; absolute positioning,G4 S7200 ; hold bed temp for 2 hours (s=time in seconds),M140 S0 ; bed heater off, 105 0.3 240 90 1 20 20 1 20 50 1 60 3000 2.93 25 1.04 G21 ; metric values,G90 ; absolute positioning,M82 ; set extruder to absolute mode,M107 ; start with the fan off,G92 E0 ; set extruder position to 0,M140 S[bed0_temperature] ; begin bed heating,G28 ; home all,M109 S150 ; set and wait for RETRACT TEMP (HIPS=150),G1 Z150 E-30 F75 ; suck up 30mm of filament,M109 S170 ; set and wait for CLEANING TEMP (HIPS=170),G1 X45 Y174 F11520 ; move nozzle over wiper pad,G1 Z0 F1200 ; CRITICAL: set Z top of pad,G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad,G1 X55 Y172 Z-.5 F4000 ; wiping,G1 X45 Y174 Z0 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X90 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury nozzle in cleanish area,G1 Z10 ; raise z,G28 X0 Y0 ; home x and y,M109 S170 ; set to PROBING TEMP (HIPS=170),M204 S300 ; set accel for probing,G29 ; Probe,M204 S2000 ; set accel back to normal,G1 X5 Y15 Z10 F5000 ; get out the way,M400 ; clear buffer,G4 S1 ; pause,M140 S[bed0_temperature] ; Set bed temp again,M109 S[extruder0_temperature] ; set extruder temp and wait,M190 S[bed0_temperature] ; wait for bed to finish heating if needed,G1 Z2 E0 F75 ; extrude filament back into nozzle,G1 Z2 E5 F75 ; extrude a blob to prime nozzle (sw),G1 Z2 E4.5 F600 ; retract 0.5mm (sw),G1 X15 Y15 Z10 F5000 ;move away from blob so S3D doesn't plunge into it (sw),G92 E0 ; reset extruder position to 0 (sw), M400 ; wait for operations to complete,M104 S0 ; hotend off,M140 S0 ; bed heater off ,M107 ; fans off,G92 E3 ; set extruder to 3 (will cause -3 retraction in next command),G1 X90 Y5 Z159 E0 F5000 ; move to cooling position and retract filament to relieve pressure,M190 R50 ; Set and wait for PEI BED REMOVAL TEMP (HIPS=50),G1 Y175 F1000 ; move to cooled position,M84 ; steppers off,G90 ; absolute positioning,G4 S7200 ; hold bed temp for 2 hours (s=time in seconds),M140 S0 ; bed heater off 110 0.3 205 60 1 20 20 1 20 100 1 100 3000 2.85 75 1.25 G21 ; metric values,G90 ; absolute positioning,M82 ; set extruder to absolute mode,M107 ; start with the fan off,G92 E0 ; set extruder position to 0,M140 S[bed0_temperature] ; begin bed heating,G28 ; home all,M109 S140 ; set and wait for RETRACT TEMP (PLA=140),G1 Z150 E-30 F75 ; suck up 30mm of filament,M109 S140 ; set and wait for CLEANING TEMP (PLA=140),G1 X45 Y174 F11520 ; move nozzle over wiper pad,G1 Z0 F1200 ; CRITICAL: set Z top of pad,G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad,G1 X55 Y172 Z-.5 F4000 ; wiping,G1 X45 Y174 Z0 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X90 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury nozzle in cleanish area,G1 Z10 ; raise z,G28 X0 Y0 ; home x and y,M109 S140 ; set to PROBING TEMP (PLA=140),M204 S300 ; set accel for probing,G29 ; Probe,M204 S2000 ; set accel back to normal,G1 X5 Y15 Z10 F5000 ; get out the way,M400 ; clear buffer,G4 S1 ; pause,M140 S[bed0_temperature] ; Set bed temp again,M109 S[extruder0_temperature] ; set extruder temp and wait,M190 S[bed0_temperature] ; wait for bed to finish heating if needed,G1 Z2 E0 F75 ; extrude filament back into nozzle,G1 Z2 E5 F75 ; extrude a blob to prime nozzle (sw),G1 Z2 E4.5 F600 ; retract 0.5mm (sw),G1 X15 Y15 Z10 F5000 ;move away from blob so S3D doesn't plunge into it (sw),G92 E0 ; reset extruder position to 0 (sw), M400 ; wait for operations to complete,M104 S0 ; hotend off,M140 S0 ; bed heater off ,M107 ; fans off,G92 E3 ; set extruder to 3 (will cause -3 retraction in next command),G1 X90 Y5 Z159 E0 F5000 ; move to cooling position and retract filament to relieve pressure,M190 R45 ; Set and wait for BED REMOVAL TEMP (PLA=45),G1 Y175 F1000 ; move to cooled position,M84 ; steppers off,G90 ; absolute positioning,G4 S7200 ; hold bed temp for 2 hours (s=time in seconds),M140 S0 ; bed heater off, 110 0.25 250 75 1 8 20 1 8 40 1 80 2700 2.94 75 0.97 G21 ; metric values,G90 ; absolute positioning,M82 ; set extruder to absolute mode,M107 ; start with the fan off,G92 E0 ; set extruder position to 0,M140 S[bed0_temperature] ; begin bed heating,G28 ; home all,M109 S160 ; set and wait for RETRACT TEMP (ALLOY910=160),G1 Z150 E-30 F75 ; suck up 30mm of filament,M109 S170 ; set and wait for CLEANING TEMP (ALLOY910=170),G1 X45 Y174 F11520 ; move nozzle over wiper pad,G1 Z0 F1200 ; CRITICAL: set Z top of pad,G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad,G1 X55 Y172 Z-.5 F4000 ; wiping,G1 X45 Y174 Z0 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X90 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury nozzle in cleanish area,G1 Z10 ; raise z,G28 X0 Y0 ; home x and y,M109 S170 ; set to PROBING TEMP (ALLOY910=170),M204 S300 ; set accel for probing,G29 ; Probe,M204 S2000 ; set accel back to normal,G1 X5 Y15 Z10 F5000 ; get out the way,M400 ; clear buffer,G4 S1 ; pause,M140 S[bed0_temperature] ; Set bed temp again,M109 S[extruder0_temperature] ; set extruder temp and wait,M190 S[bed0_temperature] ; wait for bed to finish heating if needed,G1 Z2 E0 F75 ; extrude filament back into nozzle,G1 Z2 E5 F75 ; extrude a blob to prime nozzle (sw),G1 Z2 E4.5 F600 ; retract 0.5mm (sw),G1 X15 Y15 Z10 F5000 ;move away from blob so S3D doesn't plunge into it (sw),G92 E0 ; reset extruder position to 0 (sw), M400 ; wait for operations to complete,M104 S0 ; hotend off,M140 S0 ; bed heater off ,M107 ; fans off,G92 E3 ; set extruder to 3 (will cause -3 retraction in next command),G1 X90 Y5 Z159 E0 F5000 ; move to cooling position and retract filament to relieve pressure,M190 R50 ; Set and wait for PEI BED REMOVAL TEMP (ALLOY 910=50),G1 Y175 F1000 ; move to cooled position,M84 ; steppers off,G90 ; absolute positioning,G4 S7200 ; hold bed temp for 2 hours (s=time in seconds),M140 S0 ; bed heater off, 120 0.5 240 60 0 0.5 1 0.6 1 1 1.5 0 0.1 900 0 0.1 0 2.5 1 45 15 1 45 50 1 60 1200 2.8 75 0.97 G21 ; metric values,G90 ; absolute positioning,M82 ; set extruder to absolute mode,M107 ; start with the fan off,G92 E0 ; set extruder position to 0,M140 S[bed0_temperature] ; begin bed heating,G28 ; home all,M109 S150 ; set and wait for RETRACT TEMP (TGLASE=150),G1 Z150 E-30 F75 ; suck up 30mm of filament,M109 S160 ; set and wait for CLEANING TEMP (TGLASE=160),G1 X45 Y174 F11520 ; move nozzle over wiper pad,G1 Z0 F1200 ; CRITICAL: set Z top of pad,G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad,G1 X55 Y172 Z-.5 F4000 ; wiping,G1 X45 Y174 Z0 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X90 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury nozzle in cleanish area,G1 Z10 ; raise z,G28 X0 Y0 ; home x and y,M109 S160 ; set to PROBING TEMP (TGLASE=160),M204 S300 ; set accel for probing,G29 ; Probe,M204 S2000 ; set accel back to normal,G1 X5 Y15 Z10 F5000 ; get out the way,M400 ; clear buffer,G4 S1 ; pause,M140 S[bed0_temperature] ; Set bed temp again,M109 S[extruder0_temperature] ; set extruder temp and wait,M190 S[bed0_temperature] ; wait for bed to finish heating if needed,G1 Z2 E0 F75 ; extrude filament back into nozzle,G1 Z2 E5 F75 ; extrude a blob to prime nozzle (sw),G1 Z2 E4.5 F600 ; retract 0.5mm (sw),G1 X15 Y15 Z10 F5000 ;move away from blob so S3D doesn't plunge into it (sw),G92 E0 ; reset extruder position to 0 (sw), M400 ; wait for operations to complete,M104 S0 ; hotend off,M140 S0 ; bed heater off ,M107 ; fans off,G92 E3 ; set extruder to 3 (will cause -3 retraction in next command),G1 X90 Y5 Z159 E0 F5000 ; move to cooling position and retract filament to relieve pressure,M190 R45 ; Set and wait for PEI BED REMOVAL TEMP (TGLASE=45),G1 Y175 F1000 ; move to cooled position,M84 ; steppers off,G90 ; absolute positioning,G4 S7200 ; hold bed temp for 2 hours (s=time in seconds),M140 S0 ; bed heater off, 0 0.5 1 0.6 1 1 1.5 0 0.1 900 0 0.1 0 2.5 0.1801 6 4 200 2 0 0 300 40 40 2 30 180 1 0 0 1 1.5 1 0.6 0.6 0.8 0 0.5 1 0.6 1 1 1.5 0 0.1 900 0 0.1 0 2.5 0.2501 4 3 150 2 0 0 300 20 30 2 25 180 2 1 0 1 1.5 1 0.75 0.75 0.8 0 0.5 1 0.6 1 1 1.5 0 0.1 900 0 0.1 0 2.5 0.3001 2 2 125 2 0 0 300 15 15 2 25 180 3 1 0 1 1.5 1 0.9 0.8 0.9 0 0.5 0 0.72 1 1 1.5 0 0.15 900 0 0.1 0 2.5 0.5001 2 2 100 2 0 0 300 30 30 2 15 130 3 0 0 0 1.5 1 0.75 0.5 0.8 0 0.5 1 0.6 0.98 1 1.5 0 0.1 900 0 0.1 0 2.5 0.3001 4 4 125 2 0 0 300 95 30 3 20 130 2 0 0 1 1.5 1 0.75 0.5 0.8 97 0.4 245 70 1 15 20 1 15 75 1 100 2400 2.95 28 1.27 G21 ; metric values,G90 ; absolute positioning,M82 ; set extruder to absolute mode,M107 ; start with the fan off,G92 E0 ; set extruder position to 0,M140 S[bed0_temperature] ; begin bed heating,G28 ; home all,M109 S160 ; set and wait for RETRACT TEMP (PETG=160),G1 Z150 E-30 F75 ; suck up 30mm of filament,M109 S170 ; set and wait for CLEANING TEMP (PETG=170),G1 X45 Y174 F11520 ; move nozzle over wiper pad,G1 Z0 F1200 ; CRITICAL: set Z top of pad,G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad,G1 X55 Y172 Z-.5 F4000 ; wiping,G1 X45 Y174 Z0 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X90 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury nozzle in cleanish area,G1 Z10 ; raise z,G28 X0 Y0 ; home x and y,M109 S170 ; set to PROBING TEMP (PETG=170),M204 S300 ; set accel for probing,G29 ; Probe,M204 S2000 ; set accel back to normal,G1 X5 Y15 Z10 F5000 ; get out the way,M400 ; clear buffer,G4 S1 ; pause,M140 S[bed0_temperature] ; Set bed temp again,M109 S[extruder0_temperature] ; set extruder temp and wait,M190 S[bed0_temperature] ; wait for bed to finish heating if needed,G1 Z2 E0 F75 ; extrude filament back into nozzle,G1 Z2 E5 F75 ; extrude a blob to prime nozzle (sw),G1 Z2 E4.5 F600 ; retract 0.5mm (sw),G1 X15 Y15 Z10 F5000 ;move away from blob so S3D doesn't plunge into it (sw),G92 E0 ; reset extruder position to 0 (sw), M400 ; wait for operations to complete,M104 S0 ; hotend off,M140 S0 ; bed heater off ,M107 ; fans off,G92 E3 ; set extruder to 3 (will cause -3 retraction in next command),G1 X90 Y5 Z159 E0 F5000 ; move to cooling position and retract filament to relieve pressure,M190 R50 ; Set and wait for PEI BED REMOVAL TEMP (PETG=50),G1 Y175 F1000 ; move to cooled position,M84 ; steppers off,G90 ; absolute positioning,G4 S7200 ; hold bed temp for 2 hours (s=time in seconds),M140 S0 ; bed heater off, 97 0.4 225 70 1 15 20 1 15 75 1 100 2400 2.82 60 1.36 G21 ; metric values,G90 ; absolute positioning,M82 ; set extruder to absolute mode,M107 ; start with the fan off,G92 E0 ; set extruder position to 0,M140 S[bed0_temperature] ; begin bed heating,G28 ; home all,M109 S160 ; set and wait for RETRACT TEMP (NGEN=160),G1 Z150 E-30 F75 ; suck up 30mm of filament,M109 S170 ; set and wait for CLEANING TEMP (NGEN=170),G1 X45 Y174 F11520 ; move nozzle over wiper pad,G1 Z0 F1200 ; CRITICAL: set Z top of pad,G1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad,G1 X55 Y172 Z-.5 F4000 ; wiping,G1 X45 Y174 Z0 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X45 Y174 F4000 ; wiping,G1 X55 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X80 Y172 F4000 ; wiping,G1 X60 Y174 F4000 ; wiping,G1 X90 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X80 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X100 Y172 F4000 ; wiping,G1 X110 Y174 F4000 ; wiping,G1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury nozzle in cleanish area,G1 Z10 ; raise z,G28 X0 Y0 ; home x and y,M109 S170 ; set to PROBING TEMP - NGEN=170,M204 S300 ; set accel for probing,G29 ; Probe,M204 S2000 ; set accel back to normal,G1 X5 Y15 Z10 F5000 ; get out the way,M400 ; clear buffer,G4 S1 ; pause,M140 S[bed0_temperature] ; Set bed temp again,M109 S[extruder0_temperature] ; set extruder temp and wait,M190 S[bed0_temperature] ; wait for bed to finish heating if needed,G1 Z2 E0 F75 ; extrude filament back into nozzle,G1 Z2 E5 F75 ; extrude a blob to prime nozzle (sw),G1 Z2 E4.5 F600 ; retract 0.5mm (sw),G1 X15 Y15 Z10 F5000 ;move away from blob so S3D doesn't plunge into it (sw),G92 E0 ; reset extruder position to 0 (sw), M400 ; wait for operations to complete,M104 S0 ; hotend off,M140 S0 ; bed heater off ,M107 ; fans off,G92 E3 ; set extruder to 3 (will cause -3 retraction in next command),G1 X90 Y5 Z159 E0 F5000 ; move to cooling position and retract filament to relieve pressure,M190 R50 ; Set and wait for PEI BED REMOVAL TEMP (NGEN=50),G1 Y175 F1000 ; move to cooled position,M84 ; steppers off,G90 ; absolute positioning,G4 S7200 ; hold bed temp for 2 hours (s=time in seconds),M140 S0 ; bed heater off,