Loading

List of Tronxy 3d printable modification/parts

Please Login to Comment

A usefull list of usefull prints and modyfications for your Tronxy 3d printer:

Want to add more? Just write in post below and I add it when I see it.

Most if not all of those parts should work for all 3d printers from tronxy family unless specified otherwise

Part coolers:

  1. One of the best I found untill now. I have printed it in silver PLA and even tho its very thin it didnt melt when I was printing stuff in 245C
    https://www.thingiverse.com/thing:1906391

If you have bigger fan you want to use with it that might come helpfull:
https://www.thingiverse.com/thing:2464461

  1. I used it for quite a while, its sturdy and works well however its pain in the donkey to remove it for maintenance. Also it have problems with printing in higher temp than 200C
    https://www.thingiverse.com/thing:1905198

  2. Looks like that might work for our Tronxy mashine as per this fb post (https://www.facebook.com/groups/1694483897515810/permalink/1826112524352946/)

https://www.thingiverse.com/thing:2334407

  1. Its more or less garbage. I am putting it here because its my design, some people actually use this so they prob knows better how it works.
    https://www.thingiverse.com/thing:2201957

Belt Tentioners:

  1. X axis, very good, very reliable solution, rorks on my x1 and works on x3, I suspect it would work for any 3d printer with 20x20 open on one end axis.
    https://www.thingiverse.com/thing:2020468

  2. X Axis, another one, looks more sturdy, did not test it out actually.
    https://www.thingiverse.com/thing:2732816

  3. [x1] Y axis and some other improovements, did not printed out but looks sturdy:
    https://www.thingiverse.com/thing:2716315

  4. [x1] Y axis Not perfect but I have it on my printer for 9 months and it does work no problemo
    https://www.thingiverse.com/thing:2169655

  5. [x3] Y axis. Not sure how well it works as I dont have x3 but this fella does amazing job so I thing it will work perfectly fine.
    https://www.thingiverse.com/thing:2021999

Base case

1.[x1] A case for all electronic that goes underneath your printer, its good, you can print it on tronxy x1, a little bit of gluing and you might safe some pizza cartons to make bottom for it as it might be tricky to print bottom parts but its tested by me and works great
https://www.thingiverse.com/thing:2354771

  1. [X1] Another one, looks better than previous one.
    https://www.thingiverse.com/thing:2716310

Small usefull thingos:

  1. Thumbnut screw replacement. For adjusting your bed level. Those are pure gold in comparison to metal ones that comes with the kit.
    https://www.thingiverse.com/thing:2463577

  2. 20x20 endstop fitting (its designed with z axis x1 in mind):

https://www.thingiverse.com/thing:2758352

Tronxy X3 Supercooler - hot end fan shrouds
by idig3d
fan converter 30x30 to 40x40 for Tronxy supercooler
Tronxy X3 40MM Fan shroud
Ender 2 3D Cooling Fan Duct
by razer35
Tronxy x1 40 mm element cooling fan shroud
Tronxy X3 x-belt tensioner
by idig3d
TronXY X1 X-Axis Tensioner
TronXY X1 Y-axis UPGRADE_KIT
Tronxy x1 belt tensioner for Y axis
Tronxy X3 y-belt tensioner (front)
by idig3d
TronXY X1 Modular Base
TronXY X1 V1 Control Box and base that can be printed on a X1
Endstop Holder for Tronxy x1 (or other 20x20 alu profile)

I've made (remixed in TinkerCAD) a lead screw guide for T8 leadscrew and 608 bearing https://www.thingiverse.com/thing:3677609
It works but may require more a bit of filing for the T8 hole

Tronxy X1 Z-axis guide (8mm leadscrew)