I designed this with Fusion 360. Learn Fusion 360 with my online video courses at https://www.desktopmakes.com/

Simply print and wear. Watch this video to see how I made the headband. https://youtu.be/C9bYTeK1fvg

The brim is already designed into the model so you don't have to worry about adding one.

This model was designing in Fusion 360. Learn to design for 3D Printing by taking my online video courses at https://www.desktopmakes.com/

There are three stl files. A large at 170mm, a small at 120mm, and a solid model. The large and small are both designed to print with 0.8mm walls. Note if you scale these you will affect the wall thickness. If you want to try printing in vase mode then use the solid model, scale to size, and select vase mode in your slicer.

After printing I primed and spray painted the model with a textured sandstone paint which gave it a great look. Watch this video for post processing and design tutorial using Fusion 360. https://youtu.be/9wxzN8oqzz8

Enjoy
https://youtu.be/zFFEcoNp8EY

This model was designed in Fusion 360. Learn to design your own models through my online video courses at https://www.desktopmakes.com/

Print your own Slinky. Printed at 0.2mm and no supports. After printing, take a spatula or putty knife to separate the layers. Check out the design video here: https://youtu.be/wIexWXESKUU

Designed with Fusion 360. Learn to design with Fusion 360 with video tutorials at https://www.desktopmakes.com/

This is a screw terminal block for the Adafruit Circuit Playground board. It allows you to use the board with regular jumper wires instead of alligator clips. It is designed for M3 nuts and screws. The nuts I used measured 5.4mm in diameter. Take a look at the video below for design and assembly.

https://youtu.be/vQVX-AsVE5U
https://youtu.be/YTMIqhu1OOU

Ninja Star Fidget Spinner. Print, assemble, and spin.

Learn to design this by taking the Fusion 360 for 3D Printing Course at https://www.desktopmakes.com/ A site for Fusion 360 tutorials, classes, and online learning.

Also visit my youtubes at https://www.youtube.com/desktopmakes

https://youtu.be/Fn7R9MlnLXk

Learn to design this by taking the Fusion 360 for 3D Printing Course at https://www.desktopmakes.com/ A site for Fusion 360 tutorials, classes, and online learning.

Also visit my youtubes at https://www.youtube.com/desktopmakes

https://youtu.be/GZ4QvCiovds

Geared fidget spinner. Print 4 gears, 2 sides, and 2 finger pads. Uses a standard 608 bearing.

I noticed that pennies from different years can have slightly different dimensions so make sure all your pennies are the same size. The hole size I used is 19.05mm.

Learn to design your own by taking the Fusion 360 for 3D printing video course at https://www.desktopmakes.com/

Also visit my youtubes at https://www.youtube.com/desktopmakes

https://youtu.be/GZ4QvCiovds

A fidget spinner that uses a standard 608 bearing and pennies for weight.

Learn to design your own by taking the Fusion 360 for 3D printing video course at https://www.desktopmakes.com/

Also visit my youtubes at https://www.youtube.com/desktopmakes

https://youtu.be/GZ4QvCiovds

Tri Spinner with standard 608 bearings.

Hex nut tri spinner. Uses standard 608 bearings and 5/16 nuts. Two models: a 35mm radius and a 30mm radius for smaller hands.
Learn to design your own by taking the Fusion 360 for 3D printing video course at https://www.desktopmakes.com/

https://youtu.be/GZ4QvCiovds

Batman fidget spinner. Uses stadard 608 bearings.
Learn to design your own by taking the Fusion 360 for 3d Printing video course at https://www.desktopmakes.com/

https://youtu.be/GZ4QvCiovds

A simple three ring fidget spinner. I used standard 608 bearings on this.
Learn to design this by taking my Fusion 360 for 3d printing video course at https://www.desktopmakes.com/ A site for Fusion 360 tutorials, classes, and online learning.

https://youtu.be/GZ4QvCiovds

A single bearing ring spinner. I used a standard 608 bearing in this.
Learn to design this model by taking my Fusion 360 for 3D Printing video Course at https://www.desktopmakes.com/

https://youtu.be/GZ4QvCiovds

Learn to Design with Fusion 360 with my video courses at https://www.desktopmakes.com/

Scale to desired size and print using the vase mode. Make sure to specify 0 top layers in your slicer and at least 2 bottom layers. If you print it with a brim you can use the brim as a lip on the bottom of the vases to easily pull apart the vases after being spiraled together. See video for example on how to do this on with your slicer.

Design video here: https://youtu.be/klKxqIs_vRE

Learn to Design with Fusion 360 with my video courses at https://www.desktopmakes.com/

Scale to desired size and print using the vase mode. Make sure to specify 0 top layers in your slicer and I used 3 bottom layers. Enjoy.

See design video here https://youtu.be/xFcl5PxAOlc

Print the parts and watch this video for assembly instructions.
https://youtu.be/q-PG-c92ys0

See how I designed this using Fusion 360.
https://youtu.be/V_WcjA2MBdA

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

I designed a low poly crystal in Fusion 360. I guess you can also call it an iceberg.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

https://youtu.be/Qvv3plMB3GA

www.desktopmakes.com

Inspired by http://www.thingiverse.com/thing:240158. I decided to design my own drooloops flower using Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

https://youtu.be/31JA9adF1a8

www.desktopmakes.com

Print your own GoPro Polyhedron Stand. I modeled this in Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of this design at https://youtu.be/uCU1D5wOl7o

Pantsuit Nation Earrings. I designed this in Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

3D print a pair of snowflake earrings. I designed this in Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of this design at https://youtu.be/t3Zn4I0t_ro

Print your own Peppa Pig. Print body feet and arms and assemble. I designed this in Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of this design at https://youtu.be/W2s2_lg7MWA

Print Santa's Sleigh. Print all three pieces and assemble. Watch video below to see my approach on design and assembly. I designed this in Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of this design at https://youtu.be/kLDVDBeAUQ8

Minnesota Vikings Helmet. Print, assemble, wear, and watch the game. Watch video below to see how I designed and assembled this. I designed this in Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of design here https://youtu.be/dhILRX5ncLc

A snowman Christmas ornament designed for 3D printing. Print the body and arms separate then glue the arms in place. I designed this in Fusion 360. After printing I applied a coat of primer and painted with acrylic paint. Check out video below to see my full process.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of design here https://youtu.be/DyAZyendHjc

Print this adorable marshmallow s'mores Christmas ornament and hang it on your tree this year. Learn how to design this model by visiting my youtube tutorial here:

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of design here https://youtu.be/Mqy4jFvAazU

Print this Jack O'Lantern and place a flickering led inside. I designed this with Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of design here https://youtu.be/csaliZ81daU

A great accessory for the Halloween party. I designed this with Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Video of design here https://youtu.be/Qs2AYPRk29M

Hair Comb. I designed this with Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Also, check out my website at http://www.desktopmakes.com/

Ship Wheel Pendant. I designed this with Autodesk Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/

Taco Stand and Taco. I designed this with Autodesk Fusion 360.

Fusion 360 for 3D printing design courses available at https://www.desktopmakes.com/