this is to make a 3d scan with a camera and software like 123d or remake, etc. the platform swivels 360 degrees and has markers in 10 degree increments. the camers sits on a holder that has places for a rubber band to go that hold the phone to the phone holder. the camera is on a arc and locks in via ratchet type notches, this is so you can change the elevation angle that photogrammetry needs. it needs a low angle and a higher angle. the max angle is less than 90 degrees in elevation.

a mini tripos that uses spring ratchets to hold the legs in place. the legs snap into place as does the platform, into the base. the tripod swivels and holds via friction fit.

a remix of a good design. but i improved on it.
the side spring/ratchet pawl is easily placed into position after you insert the rod, by spreading the prongs apart to slide over the rod and into position.
i included a little holder piece onto the rod to keep it from warping up as it did without it.. but it easily come off after printing.

*changed spring design to be more flexible

• i changed sprocket design and spring to match.

a remix of Keychain: Minion Loves 3D Magic Makers
by 3DMagicMakers.

this is a gun design prop, with the barrel being held by a spring. you push the bbl forward against spring to remove dummy bullet. you can push bbl forward and lift to remove bbl.
spring is used as a silencer/baffle too.

print in place calipers. you will need to do some careful separating the sides a bit. i was worried it wasnt going to separate, but i carefully used a blade to reach in between the sides especially near the rotating axle area. but you see my results.
i used 32% infill. but lil more wouldnt hurt.

this uses cranking inward on the handles to turn the cutters.

• i added a 3 handle crank that is smaller to keep from hitting table.

• i added a hex hole for a 1/4 hex bit to turn via a power screw driver or power ratchet

this could be used for shredding kitchen food to add to compost bin. which is why i made it.
or shredding veggies for salads, salsa,
smoothies, etc. for food use food safe pla.

i made this to avoid the hassle if plastic gears stripping.
the cutters hav a socket built in for the included ratchets ( ratchet is remix of clevins pocket ratchet).
the ratchets rotate inward toward the cutters. obviously you would move both ratchets inward at the same time. but.. having added the cutter ratchet stop you could actualy just turn 1 cutter if u want.
i added a ratcheting/spring mechanism to keep the cutters from moving backward as you move the ratchet handle back getting reading for another handle ratchet turn forward.

this could be used for shredding kitchen food to add to compost bin. which is why i made it.
or shredding veggies for salads, salsa,
smoothies, etc. for food use food safe pla.

use near 100 percent infill for strength for the cutters and ratchet springs. the others can be lower.

this shredder version lets you print the box in halves. after placing the cutters into the bottom, you then place the top and it snaps closed with latches on the bottom.
i included both cutters in one file for for convenience and separately for those that want to print one at a time.

i added a ratcheting socket crank (remix of clevens pocket wrench design) so you dont have to turn all way around as with regular socket , wrench, or crank.
i included a hand crank for those of you who prefer it.
i also added a cutter with the socket built in, on the end. i liked this idea for the reason that the ratchet handle can get closer to the gear for better torque.

this could be used for shredding kitchen food to add to compost bin. which is why i made it.
or shredding veggies for salads, salsa,
smoothies, etc. for food use food safe pla.

use near 100 percent infill for strength.

i made this to make it easier to turn the knob. just put a finger on one of the tabs and push to turn.. i made it thin enough to let the leds show through.

i made this dial to make it easier to turn. you can turn using the inside area or with one finger use the outside area. i made this as minimal as possible for time saving and filament saving

this is a print in place design. use support and raft. u will have to break the shafts free of
the box with a little twisting back and forth. then your good to go.
i have cut flats on the shaft at the places where it needs freeing, cuz this is where the
filament adhered the most and made it the hardest to free. the flats on the shaft don't affect

i included a crank. but maybe you can use a 17 mm wrench or adjustable or socket.

the turning of the shaft in the hole in the box.

this could be used for shredding kitchen food to add to compost bin. which is why i made it.
or shredding veggies for salads, salsa,
smoothies, etc. for food use food safe pla.

use near 100 percent infill for strength.

i have changed things since first uploaded.
along with the flats, now i have made the box holes bigger to make it easier to break free.

this is to carry frozen fish food balls from the freezer to the fish tank and dropping it in. cuz i hate grabbing it with my hands .

Merida from Brave

remixed a nice looking flower by hex17, into a stove knob.

hello kitty stove knob

a smoothed version.

superhero stove knobs

this 1 shaft shredder uses the side vanes in place of another shaft/set of shredders to restrain the material being shredded while the cutters do the rotating and cutting force.

with this shredder the cutters are placed in the bottom box part and then the top box part snaps onto the bottom. cant get any simpler than that. you can print and use the crank, or you can use adjustable wrench,

this could be used for shredding kitchen food to add to compost bin. which is why i made it.
or shredding veggies for salads, salsa, smoothies, etc.
for food use food safe pla.

use near 100 percent infill for strength.

with this shredder the cutters slip inside the box and the end pieces hold it in place with c-clips. i added a 3/8 in. hex for those that want to use a socket or wrench.

i fixed the ears. the original stl ears holes i were messed up.

wonder woman cookie cutter with back to keep inner lines from moving cuz they are so thin and outer edge to help lift off cookie. the back has holes to help remove cookie from cutter. i raised the inside to make deeper marks. the idea is not to cut out the cookie shape but to make good impression into the cookie. if used to cut cookie it may be hard to remove doh from cutter. but try an see what works best for you..
i included the one my niece uses it for play doh. :)

this is a variation of my tube squeezer. it uses a spring tension and ratchet mechanism also. with this one you turn the spring to tighten the tube. the spring and rod are one piece and so you will have to meticulously pick out the supports from inside the spring are but will not be a problem. i used 60% infill for the spring piece but u are free to try others. use supports on all but the cap. and use raft and supports for the rod/spring as it is laid long wise along the table. the rod spring and an added support on the end to keep it from rising off the bed but will come off easy after printing.

my design of a a tube squeezer. it uses a spring tension and ratchet mechanism. i added a piece on the end of the rod to hold it down as it popped up on me while printing so i added it. it comes off the rod easy after its done.
the spring printed easy with round facing the table. just use raft and supports.
the cap needs no support, flat side down.
i layed the frame with a flat side to the table and use supports, no raft.

baby groot standing w base. included a baby groot with a t-shirt on request.

a remix from http://www.thingiverse.com/thing:2014307. i combined head in body and i made a base. and printed it smaller.

this is a print in place remix. well the handle still needs to be fixed (glued, etc.) together ,but no bolt and nut are needed as those 2 parts are a print in place hinge. i didn't see the need for the rear to be so long either so i shortened it.

see the original here: http://www.thingiverse.com/thing:108567

this is a multipupose sign thing. you just insert the sign part you want, into the base part and flip up to view.
i use the fish sign to show that the fish have been fed, when it is up. and not fed when it is down. you can use it for anything you like.
signs included are an angelfish, moana , dory , and tinkerbell..
the base is printable in one piece.
the base can be remixed into your sign designs. or whatever you need to flip.

Customized version of http://www.thingiverse.com/thing:1808029

Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1808029

i tried the exact size i measured at 2.9mmbut the were to bit. so i tried 2.5.. and it made it bigger at just the right size.

here is my version of a mechanical horse. i included the step file in case anyone wants to load it into software and build it. i animated it it fusion 360 and all the parts work together nicely. also this needs the links pins to keep the links together. you will also have to use 3d software to make a stl file of each part to print them and then assemble them.