A low profile drip tray for your wet Aeropress.

The Aeropress is so great to use and clean up after you make your coffee, a quick rinse under the tap, this is somewhere to put it while it drys.

The Aeropress model used in the renders came from the Fusion 360 library, modeled by Ryan Arnaudin.

https://gallery.autodesk.com/fusion360/projects/aeropress-coffee-maker

Edited to soften the edges (added fillets) where the filter top and lower section locate, should now be easier to put it together.

Going on holiday for a week and wanted to take my Aeropress, didn't need a whole load of filters so made this carrier to keep things neat.

Made it fit as one piece to the Aeropress body.

Has a 6mm storage space for filters, holds about 30-40 filters easily, also has a fitting lid to keep the filters in place.

The Aeropress model used in the renders came from the Fusion 360 library, modeled by Ryan Arnaudin.

https://gallery.autodesk.com/fusion360/projects/aeropress-coffee-maker

Keeps 4 beer bottles organised/stacked in the fridge. Lets the good wife keep the fridge stocked with other less important things....

A holder for my Dualshock 3, the mounting is set for my 50mm shelf.

Just a little plastic repair for my brothers hoover.

Hoover gl71gl04001 brush bar holder

A quick and dirty headphone tidy.

HTC 626 dash mount for Ford Transit. Just remove one of the switch blanking plugs in the centre of the dashboard.

Stand to hold my LG Urbane smartwatch charger. Printed in two pieces then glued. Room in the bottom for 2 pence coin for added weight.

A phone stand with room for USB cable. There's room underneath for 2x 2 pence pieces to add some weight to the base.

Customized version of http://www.thingiverse.com/thing:1337584

Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1337584

I'd printed a mount for a screw adjustable z stop then glued it on to my X axis mount, this is a printable version without glue.

Also I wanted to reprint in white PETG.

Just a lid for a dog food can.

Customized version of http://www.thingiverse.com/thing:1098806

Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1098806

Customized version of http://www.thingiverse.com/thing:1289978

Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1289978

Cover for HTC 626g.

Charger port over sized to fit magnetic charging adaptor.

Customized version of http://www.thingiverse.com/thing:720041

Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=720041

Customized version of http://www.thingiverse.com/thing:720041

Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=720041

Lots of spool bearings on here, none did what I wanted.This one takes
http://www.thingiverse.com/thing:150768
and fits it in to a spool adaptor,

Uses 6mm ball bearings. Small indents in inner race edges to ease bearing input.

PSU cover for Hictop 3DP11. With holes for socket and switch.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/29vxqiH0BxQ

The original part was split in to pieces this is just reset designed as one part, and the nut was resized.

Customized version of http://www.thingiverse.com/thing:1322072

Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1322072