Hey! This thing is still a Work in Progress. Files, instructions, and other stuff might change!

R. Maker - Mark I

by Mr_MegaTronic Sep 18, 2011
Download All Files

Thing Apps Enabled

Please Login to Comment

I love the original heart inside Mr. Maker. :) Where can I find the file for the heart that snaps in too?

I just finished printing this little guy as one of my first prints. Quite the learning experience. I had the same problems as some have posted about.

My lazy mans fix for the feet clips was to do the following.

Sand down the feet where the clips broke off flat.

Scale a copy of the shoulder pins by .7 and print them on their side.

Use acetone to glue the new clips in place (Have yet to see how well this works in the long run).

Also, I didn't like how loose the arms were, so I printed out a hollow ellipsoid from blender sized to just barely fit inside the shoulder clips. I cut the ellipsoid in half with a hobby knife and placed it a half inside each pin after it was in the robot body but before the arm was attached. The ellipsoid half provides extra resistance which gives a nice firm movement.

I know these are not the "right" ways to fix the small problems, but they worked for my purpose.

Now you can print a smaller one to go on his build platform! Worthy winner.

My MakerBot is here! YAY! I uploaded a photo of the print they gave me. Stay tuned! Now that I can validate my designs, I'll be updating the Mark II with improvements to make for a better print!

congratulation Erik i knew u would win

Great robot, I printed this and learned a few things myself. A few quick tips:

-The clips on the bot spool and legs broke upon assembly, consider thickening the cross-section or using another method of attachment. My bot did not reproduce these very well, they were very jaggy and weak.

-The attachments for the wrist and head work VERY well. Consider using this flat design to fix the strength problems above.

-The shoulder joints worked ok. They are somewhat loose and allow the arm to fall off easily. More cross-sectional area would be helpful. I think using flat design like for the wrists or neck would be very strong and functional.

-The visor clips located on the head also broke. This did not present a problem though because there was a very nice press fit between the visor and head. Clip geometry is not necessary for these two components to mate. Good press fit on the eyeballs too.

-I use 3mm filament and had to drill out the head to make it fit, not a huge deal.

-I printed the body at 35mm/s and 15% infill, .4mm nozzle, turned out good, build time: 4.5 hrs.

A very cute robot, everyone i showed it to, loved it. Excellent design and great assembly instructions. Very good build. I think with a few minor modifications at the joints this robot can be made a lot more robust.

Thank you for designing this. Well done.

Is that Maker-tangelo?

Naw, he had a orange visor. This is Makephael.

His brothers Makernardo, Makertangelo and Makeatello were unavailable for the photo-shoot.

Hi, clips that print vertically like the ones built into the feet and the face are very weak, suggest you replace with clip holes so we can print separate clips horizontally.

Also, the head clip is a bit thin, could be a little fatter for strength.

I suspect the reel clip may be rather tricky, I haven't gotten to that part yet. I may fatten it up a bit first.

The clips on emmet's screwless cube gears are lovely, for reference.

I added some holes in the head for LED
leads and a little space for the flange on mine :)

Yes, for version 2 you should really think about either making the built-in pins much larger/thicker or replacing them with separate pegs and holes in both parts that join together. It's a common problem with these connectors. I broke them several times and had to use a little super glue to re-attach the pins.

My only other issue with it is that the body is really prone to splitting because it's so large and boxy. I'd suggest splitting it into multiple pieces, but I'm not sure how best to do it visually because it looks great having that big large opening to put other prints inside.

Thank you for the information! Very useful! I will be indeed taking your and other's advice regarding the pegs. I think I have a good idea on the body. Being a graphic designer first and foremost, this was an exciting experiment. This community and people like you are awesome as I would have no other means to test this out. I don't have any of these tools to validate my designs and I GREATLY appreciate you and others taking the time to print him. I'm ready for the next step in this project and just in time because the competition is really heating up! This weekend, I'll be putting up v2.0 with the upgrades and quite a few surprises.

Because I NEED that Thing-o-matic!!! :) Oh the things I could make! I have so many ideas! Just not a lot of means ($) at the moment... :'(

I'm designing a 3d printable MUSIC BOX!! Among other things... It's so expensive to use my local hackshop's printers and I have a lot of tests to prin
t to get things just right.

Also this is a fun learning experience. Even if I don't win, I will have learned a lot and look forward to future opportunities.

Thanks again!

I love this guy, I'm definitely going to print one tomorrow!

I love Mr. Maker. I just hploaded my version. I have not made the back pack yet because I don't have any of the small fillament.

I don't know how you do it, but my vote for the mascot goes for Mr. Maker.

Not only does it show off the capability of my TOM it is hackable at different levels. First, you can make a copy with different colors. You can hack it to include two different color back packs for the duel color printing
version. A high level of hacking might include modifying the head so it is hollow. Include a battery, LEDs and a circuit so the LED eyes will blink.

Incredible! It looks wonderful!

I made the holes that the eye plugs slide into the right diameter to take standard T1 LEDs. My idea was to incorporate that but I initially couldn't decide on the hardware. I'm working on a 2.0 version that could include a switch, battery case and wiring holes/channels. But I felt for v1.0, the
community could take a swing at it and possibly do better than I. ^__^

At the moment I don't have the ability to print my creations, but I hope to someday soon, and I look forward to continue to churn out projects. This is FUN!

Oh I'm curious, did the pegs just print and snap in snugly? Did anything need to be sanded or relieved of material to fit? Do the feet and arms hold their position? I was worried that I screwed up the tolerances of the holes and pockets and either the pegs wouldn't fit, they'd break bring flexed or were too loose to allow Mr. Maker to be posed.

I am amazed at how well the thin build platform printed and the claw fingers. They look PERFECT!

There I go, gushing again. You veteran printers will have to excuse my giddy excitement. ;)

The head snapped onto the body. This was the best joint. I touched the holea in the body to accept the shoulder pieces.The claw hands snaped well onto the arms. The worst were the feet. I couldn't get in there to touch the holes for the feet.

A couple of my friends shamed me into making the reel. It took some exacto knife work to get the four legs to snap into the four rectangular holes. A slight touch on the hole on the back of the body allowed the reel to click in.

I dropped Mr. Maker and the feet pegs broke. I suspect they partiall
y broke when I installed them. They just arn't very strong. I cheated and attached the feet with acetone (love that smell).

Good to know! Thanks you! If you don't mind, I'd like to see a photo of the spool if you have a chance.

The picture showing the spool attached to his back is shown.

By-the-way, triffid_hunter 's comments about the clips have merit.

Excellent! I am working on a v2.0 that incorporates a lot of everybody's wonderful advice plus a few surprises of my own. Do an 'ol one-two submission for the contest. I do appreciate the advice and I thank you once again for taking the time to print and document!

This is so freaking adorable. I need to get my hands and extruder on some gold and crimson plastics.

Very nice job. Are you using Inventor Pro or Edu version? I don't suppose you would post the Inventor source files?

I have Autodesk Inventor Pro 2012 and I can most certainly post the source files. ZIP AHOY!

At my work (I work at an Advanced Dental Education center here in Seattle) we are tooling up with the latest intra-oral 3d scanning technology and are working with companies to develop cutting-edge diagnostic work-flows using 3d scans of patient's teeth. As part of the upgrades, we culled into ou
r existing Autodesk Subscription (I use 3d Studio MAX for all of my CG and VFX work) a license for Inventor Pro 2012. A piece of software I have never seen or touched prior to last Thursday. On Friday, I poked around in it and on Saturday, I created Mr. Maker.

I have to say, Autodesk Inventor
is perhaps the most enjoyable modeling application I have ever used! The modeling engine is mostly non-destructive and unobtrusive. The tools are obvious and the interface is clean and direct. I may be a veteran 3d studio MAX modeler, but I have never taken so well to such a vastly different mode
ling workflow/paradigm!

Okay. Enough Gushing...Sorry. ^__^

I decided to start with the body. This is not a quick print but it looks great! It has a representation of the injector and the table. I nice feel to this print. I'll add images as I finish each print.

Well, I just printed the head and joint. Everything went well. His head turns like it should. I will resume printing late tomorrow.

It is looking excellent! Have a good evening and thanks!

A few moments after I posted the above picture I started to print the head. As I sat next to the machine I noticed two cracks started to appear They are shown below highlighted by red arrows. Number 1 was the first and the longest while number 2 is smaller. There two more smaller ones on the opposite side down low.

I had trouble with the shoulder pegs. The legs on each peg broke off. I had no problem with the other pegs. I believe the direction of fiber layup is wrong with the shoulder peg. Where as the other pegs have the fiber layup in the direction of the legs not cross wise.

Excellent! I very much appreciate you taking the time to print this! It looks better than I imagined! Are you Printing on a Thing-o-matic?

I wonder, what the primary cause for the layer separation usually is. Is it too dense? Did it cool too fast? Is this something that I need to deal with in the design phase, or the print phase?


As I said, this print looks very very good. I love it.

When my TOM finished printing the body the machine shut down in the normal manner. The body stayed on the heated plate for about 20 minutes cooling down. I guess I would wait until some one else prints it. If the new one cracks in about the same place then I would look at possibly a redesign. As far as my body goes, I could never through it out, I'm keeping it, crack and all. Besides the crack is very narrow.

How long did it take to print the body? There is a workshop around where I live that has a few printers and charge by the minute so I was was wondering how long for approximate cost estimating.

Sorry Eric, I made the mistake of not noting the time. It took a long time. I mowed both the front and back yard, changed the oil in the snow blower getting ready for the winter, took a shower and did some reading.

@ErickJDurwoodII: Layer separation is a print setting issue. :) I'm looking forward to printing this too!


What do you mean by "..setting issue..."?

@jimcook: Cracking is almost always due to skeinforge/print settings. This post gives some possible reasons, such the infill being too high and the number of shells being too low. http://www.makerbot.com/blog/2011/05/31/untangling-skeinforge-shells/http://www.makerbot.com/blog/2...

And the winner is... I don't think it will be long until you have your own printer. I luv that little guy.

Are their LED holders in the eye sockets?

There should be LED holders in the eye sockets.

Extra credit for designing in a battery holder and switch somewhere too.

Extra extra credit for wiring channels.

I designed the visor to allow for that, I was trying hard for printability and character. Until I can get this guy printed somehow, I'll have a better idea on how I can incorporate those features into version 2.0 ^__^


Awesomely recursive and recursively awesome!

Oh, and for anyone who can help, this is my first upload and I'm not sure why the STL thumbnails are in weird positions. Probably a problem with the STL itself. Is there a straightforward method for re-positioning a model? I'm still cutting my teeth with the different software.


You could load them up in ReplicatorG, use the centre/place-on-platform functions, and then re-save the STL files.

And just like that! Thanks!