Laser cutting of a sheet high-quality galvanized steel on a sheet of high-quality galvanized steel, according to our redesign, with the following improvements:
Dramatically lightened the Y axis carriage, in order to improve dynamic behavior.
Filament support included.
Fixed the problem with the upper left side (the extruder clashed with it), and also the problem of the nut that clashed with Y axis motor.
Modified the distance between the two pieces that make the Y axis tensioner, so as to hold the F624zz bearings with washers. Also, modified the hole diameter.
Y axis now measure 350mm, the extra 9mm are added on the front side.
Y axis bearing holder and Y axis belt holder are replaced by printed parts, as the metalic parts caused troubles.
2. Theaded and Smooth Rod Kit:
2x 375mm Smooth Rods – Stainless Steel
2x 350mm Smooth Rods – Stainless Steel
2x 320mm Smooth Rods – Stainless Steel
2x 300mm M5 Threaded Rods – Stainless Steel
1x Smooth Rod for filament support
*The cutting is done by hand, so that the meassure can be slightly higher (+ 1mm or similar) not lower.All rods are shipped without burr and the edges filed down properly.
3. Printed Partds:
Manual advance wheel
Layer fan 4020 support
Cable holder chain
X Motor and X ilder, with tensioner for F624zz bearing
X axis carriage
X axis endstop support
Separators for motors
Corners for calibrating the Heatbed
Y axis endstop support
Z Axis upper side for MR105
Z axis endstop support
Box for Ramps 1.4
Cover for power supply
Printed parts for a smooth running of filament
*You can choose the colour, otherwise, we will ship them randomly.
Mega 2560 R3 (Compatible) 16u2
Ramps 1.4 (with aluminium heatsink)
Stepper Motor Driver DRV8825 x 4 (with heatsinks and thermal double-sided tape)
Heated Bed MK2B (12v/24v) (or the version you choose)
Termistor 100k Ω NTC 3950 (1m wire)
5x Stepper Motor Nema 17 - 17HS4401 or 1703HS168A (the rack has a flat part + wires)
1x hotend All Metal V6 equipado with ceramic heater, with thermistor, and fan3010. Nozzle at your choice
12v 30a DC Power Supply with switch, printed part, 1mm2 wire y power adapter
LCD with rotary encoder, SD reader y adapter for Ramps
Kapton Tape15mmx33m Insulating tape resistant to high temperatures, highly recommended, as it serves to insulate the connectios (for example the Heated Bed) and to hold cables.
Thermal Insulation for Heated Bed
Increases the rate of heating of the bed, reduces energy consumption, and protects the electronics
(We recommend to isolate with kapton the part in contact with the Heated Bed)
1x Meter shrinkable 2mm2
HeatBed wires (1mm2)
1m protection for cables (spirals) y flanges
5. Movement Kit:
12x Linear bearings LM8UU
4x Angular bearings F624zz (for X and Y)
1x Angular bearings 623zz for extruder)
2x Bearings Mr105zz (for Z axis)
2x Bearingss 608zz for the filament coil
2x Couplers Shaft 5x5mm
2m Belt GT2, made of neoprene with reinforcerd fiberglass
2x GT2 Pulley, 20 teeth, aluminium
6. Nuts and Bolts Kit:
1x Mk8 extruder pulley for 1.75mm
M3x6 - 2 units
M3x8 - 14 units
M3x12 - 64 units
M3x16 - 7 units
M3x20 - 4 units
M3x25 - 8 units
M3x30 - 8 units + 1 fully threaded
M3x35 - 1 unit (with spring and 2 washers)
M4x8 - 2 units
M4x20 - 3 units
M4x25 - 9 units
Setscrew M3x10 - 1units
4 x M3 DIN 9021
12 x M3 self locking
4 x M4
61xM3 self locking
1xM4 self locking
4 x Springs for Heated Bed
More from 3D Printers
Save to Dropbox
If you’re logged into Dropbox, you can save directly to Dropbox.
Show Some Love
Say thanks by giving HTA3D a tip and help them continue to share amazing Things with
the Thingiverse community.
Remember to come back and post what you've printed as Make.
It's good for the designer and the community (that means you)!
To post a Make, come back to this Thing and click Post a Make.
Or, you can use the Thingiverse Mobile app found on
and the Apple App Store.