Optimized Nonlethal Door Stop Multitool
by ChrisMUC, published
Use This Project
Give a Shout Out
If you print this Thing and display it in public proudly give attribution by printing and displaying this tag.Print Thing Tag
Nonlethal Door Stop Multitool
- Optimized downside to Maximize the grip performance for holding the door in place, while on the other hand smoothly slipping in under the door when placed. If you want to add more-extra-ultra grip to the downside of the door stop you can use a rubbercoating. I tried the spray-on version of Plastidip and it works really great for this purpose.
For your information, this is what I used: http://www.plastidip.de.com/produkte/plasti-dip-flussiggummi/
And best of it: you can remove the coating easyly if you don't like the result. Probably you can find something similar near you in some DIY store, hardware store, home improvement store or in a shop for car supplies. I found it in an electronics store.
- Buckled upside to hold the door in a firm and secure grip.
- Extra Big hole (~42mm diameter) with Extra smoothly rounded edges to pull it out comfortably with 2 Fingers or even with gloves.
- Safekeeping by hanging it over the handle of the door is possible for most doors due to the Extra Big hole. So you have it at hand in a door stop / self defense emergency.
- Easier slipping under the door even with a small gap to the floor, due to smoothly rounded tip and optimized design of the downside of the tip (reduced size of the first to teeth).
- Suitable for ~4mm-40mm gaps without scaling. (Just a guess based of the dimensions, to be verified in experiment. Could be up to 50mm max.)
- Wall and handle protector. Put it behind the door to avoid slamming the door against the wall. (Try it with the round end facing the door, too. Depending on the size of the handle and the character of the floor this can give better results.)
- Windows can be kept open with it, too. (Not talking about the software.) Try to put it in the gap at the hinged side of the window.
- Optimized for easy printing on FDM machines (i.e. Ultimaker, RepRap,...). You should be able to print it without outer support, for details see the section instructions.
- Childsave. It is big enough that it can't be swallowed and does not have sharp edges. If you print it with the right material it is non toxic, too.
- Portable. It is light weight and has an Extra Big hole to grab and attach to things so it is really portable. If you want to transport it with your bike, you could just hang it around the handlebar. You could also attach a string and hang it around your neck for transport. If you transport it with your car you can attach a string to the hole and hang it around your rear mirror as an ornament, too.
- No assembly needed. It is just one piece so you don't have to worry about a difficult and time consuming assembly. It is usable right off the printbed.
- Customizable. You can add some rubber coating to the downside to adjust the grip needed to the floor and door you want to use.
- Nonlethal self defense tool. Hold it with two fingers in the Extra Big hole and just think about it. If you know what a tactical pen is, you know what I mean. Probably this is the first tool you have at hand when the Zombies try to rush into your home... Update: I thought about it again and probably this is not such a good idea, because the Nonlethal Door Stop Multitool is nonlethal and the Zombies are already dead. Seems not to match. You could instead try to impress them with your printing abilities and try to involve them into some kind of communication about it. (It is even more probable that a Zombie will communicate with you about 3D-printing than the Nonlethal Door Stop Multitool will do any serious harm to him or her...) Caution: Update: As Gyrobot mentiond in the comment, there is a chance that the Optimised Nonlethal Door Stop Multitool could be lethal, too. You could bore someone to death with it. I wonder if this could work with the Zombie issue mentiond above....
- You can use it as an ornament by hanging it around your neck. The rappers hung alarm clocks around their neck in the '80s, so why not?
- You can use it to build a trap. Remove the handle of the door on the inner side, hold the door open with the door stop, attach a tripwire to the door stop. When somebody enters the room they release the door by the tripwire and the door closes. Works best with self-closing doors...
- Use it as communication enabler. Just put it on your desk at work. Somebody will ask what it is. And whoosh, you are right in the middle of a 3d-printing discussion. Don't forget to print the Thing Tag. Just in case you are asked... http://www.thingiverse.com/thing:200571/attribution_card
- Use it to test your 3d-printer. The Door stop is pretty easy to print, so the frustration factor should be minimal. And after printing you have something useful to play around with. And even if the print is not fully completed, it will probably work to stop a door. And failed prints tend to attract people, who ask you about it. A perfect print is good, but to induce communication a failed print is far better.
- Use it as door stop this is what it is intended to be. And it works pretty well for this purpose.
Probably no one here reads so much text, so it seems not to matter so much what else I write here about the mere unlimited possibilities you have with this piece of plastics. But if you have more ideas about how to use this tool, you are invited to post a comment.
- The door stop was build from scratch and
inspired by thing 144708, Stopper of door No2:
- The description was inspired by thing 35518, Blockystar:
- and thing 35560, The Warble Wobble:
Thank you for your inspiration.
The design was developed in FreeCAD. http://www.freecadweb.org
Thank you for making such a powerful software available to the public!
- The door stop was build from scratch and
Thank you for visiting!
- Remixed Non-Lethal Door Stop By arod24 [Amauris Rodriguez]:
Door Stopper by alexhbaiu [Alex Hbaiu]:
Thank you for sharing your creativity!
I printed the door stop with these settings:
- 0,1mm layer (to produce a nice surface and to make it more stable.)
- 1mm walls (to make it strong enough to really stop a door.)
- 20% infill (If you don't use any infill the part will probably work afterwards, but the top surface could have problems because of the bridging needed. There is no extreme bridging, so it could work. I printed it with infill to make it stronger,too.)
With these settings and a speed of 50mm/s it consumed 4h 15m of printing time.
Upgrade this Thing with Thingiverse AppsCustomization
Edit, personalize, or revise this ThingTools and Utilities
Repair, slice, or enhance this Thing
Optimized Nonlethal Door Stop Multitool by ChrisMUC is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.
What does this mean?
- You must attribute (give credit) to the creator of this Thing.
- You must distribute Remixes under the same license as the original.
- Remixing or Changing this Thing is allowed.
- Commercial use is not allowed.
Show Some Love
Say thanks by giving ChrisMUC a tip and help them continue to share amazing Things with the Thingiverse community.Tip Designer
We're sure ChrisMUC would love to see what you've printed. Please document your print and share a Make with the community.
To post a Make simply visit this Thing again and click I Made One to start uploading your photo. It’s even easier to post a Make via the Thingiverse Mobile app (available via Google Play and Apple App Store).