Version actualized as of feb. 15th, 2019.
All moving parts went through a process of changes. These got their own thingiverse pages:
- X-Carriage, Linear, Modular, 20x20 V-Slot by printingSome,
- (I don't use this any more, because the above is a new version of this):
X - "3-wheeled or Linear Railed Modular X-carriage (D-Bot Core_XY 3D Printer)" by
There is a 3-wheel version and a linear version and modules for the E3Dv6, the
Cyclops, the Chimera, with bowden tubes as well as with nimbles.
- Y - "Y-Carriage_for_20x20_X-Rail" by printingSome,
- Y - "3-wheeled Y guide goes linear" by printingSome,
- Z - "D-Bot_Linear_Z-guide" by printingSome"
I now can use the straight mounts, thanks to:
- Z - "Bed_Hoist_for_a_3DPrinter (D-Bot, CoreXY)-_Version_2" by printingSome
- Electronics Box:the Rumba version of "Ramps 1.4/Rumba Enclosure for Vslot" by printingSome,
- "Ball_Foot for D-Bot by printingSome" dampens well with tennis balls.
- "RepRapDiscount Full Graphic Smart Controller" by Trigubovich
for which I made some V-slot supports here
- 3-point supported bed: "Präzisionsplatten - 326x326mm (Sparkcube XL) 3 Punkt" from filafarm.de, heated with a 300x300mm 220V silicone heated bed from China. I planned to use it with a PrintBite from Flex3Drive, but that was a waist of money, so now I am using Ikea mirrors 300x300mm and hairspray.
I gave a little twist to those bed supports: to diminish sideways motion of the bed I now use 3 M3x80 bolts. Normally I don't provide sellers for general stuff but I found them hard to find, so here goes:
These are only threaded over the last 34mm, so when you screw one in a support, using the inbuilt nut, which has to stay, it ends up gliding through below the bottom. There you can put a couple of washers and for instance "M3 Rosettes for Spring-loaded Platform Adjustment" by L0L0,
on it. This gives just that bit less room for sideways movement and the absence of thread makes the vertical movement smoother. Provided that the bolt glides easily through the support with nut. You have to check for that in advance, because the bolts can vary just that much and the nut, which I have glued fixed, has to be in line whith the hole through the support. Rethreading the nut once helped too. Of course check also during and after mounting the supports etc. You can secure the heads of the bolts with glue, when they tend to turn with the rosette, but I for now don't feel that's a problem.
So, no more lead screws, though if you use those I still can recommend to have a look at
One can buy a cheap but beautiful cover for the Solid State Relay, which covers all the isolated parts and leaves the hot spots open for the world to enjoy. ;-(
It seemed better for my health to make a less inviting cover.
The Y-Endstop, a bit more adjustable then the original one, can be used at the front and the back, see picture, and accommodates a type KW11-3Z 5A 250V microswitch as well as one with some electronics around it (as in the original D-Bot, I think, don't know type number, sold as an "endstop").
You'll have to check for yourself if it suits yours. The distances from center wheel to the rail are ca. 7 and 11mm vertically respectively and ca. 3mm sideways.That 11mm is a bit much, but I couldn't get it less and it works with my stuff. ;-)
The Z-endstops you see go with the linear Z guide.
As for the electronics, I now use the rumba, but also with the Ramps1.4 I used drv8825 for the X- and Y axis with 1/32 microstepping and A4988 (1/16 microstepping) for the Z-axis. That last one was a great improvement when I still used the lead screws and wheels, and why not keeping it that way, although all my troubles with lifting the bed, with 2 or 3 lead screws and with 3 or 4 wheels, are over. Everything goes light and easy with the bed hoists.
For the nimbles I use the A4988 as well (advice from the manufacturer).
Edit (03-02-19): added link to my Y-Carriage_for_20x20_X-Rail
Edit (15-02-19): actualized pictures and links (last one was the 2nd version of Bed_Hoist)
Edit (29-03-19): exchanged the soft balls in the ball feet for tennis balls: much less swaying.