Radial Fan Fang E3D V6 40mm fan Remix

by ericd_86, published

Radial Fan Fang E3D V6 40mm fan Remix by ericd_86 Jun 30, 2017
0 Share
Download All Files

Thing Apps Enabled

Order This Printed View All Apps

Liked By

View All

Give a Shout Out

If you print this Thing and display it in public proudly give attribution by printing and displaying this tag.

Print Thing Tag

Thing Statistics

12021Views 1285Downloads Found in 3D Printing


E3D V6: http://amzn.to/2wZBcBE

UPDATE 08/24/17
I am using the ABL stock mount from Timothy Hoogland
ABL Mount: https://www.timothyhoogland.com/download/creality-cr-10-ezabl-sensor-mount/?v=7516fd43adaa

UPDATE 08/07/17
So I finally got around to installing this model to my cr-10 and tested it. What I found was that PETG works the best. If you plan on going to temperatures of 270-300 degrees, then I recommend adding a small strip of Aluminum Foil Tape ( http://a.co/if9dAdt ) to reflect some of the heat near the heater block, seen in the above picture.

The fan used on the fang is a bit more powerful then stock and is nice upgrade and helps with the quality of the print. I used the stock 40mm fan to cool the E3d V6.

I only have about 12 hours of print time with the E3d V6 so far but, I can say quality has gone up on the models that I have printed.

I combine the radial fan fang from jneilliii and the short E3D V6 40mm fan mount by lethala.
I also cut down the fang's tips by 5mm. I am using this for a Creality CR-10 but can be used with certain other printers as well.


I am using this model from Bandanam4n to mount the E3D to the printer: https://www.thingiverse.com/thing:2182924

Note: I have printed this and tested if the components fit and checked the clearance of the nozzle, however, I have not tested this model on an actual printer. (still waiting for my cr-10 in the mail)

Print Settings

Printer Brand:

Robo 3D











I used PLA for this model and it should work fine, if not the PETG may be a better option.


More from 3D Printing

view more

All Apps

Auto-magically prepare your 3D models for 3D printing. A cloud based 3D models Preparing and Healing solution for 3D Printing, MakePrintable provides features for model repairing, wall thickness...

App Info Launch App

Kiri:Moto is an integrated cloud-based slicer and tool-path generator for 3D Printing, CAM / CNC and Laser cutting. *** 3D printing mode provides model slicing and GCode output using built-in...

App Info Launch App
KiriMoto Thing App

With 3D Slash, you can edit 3d models like a stonecutter. A unique interface: as fun as a building game! The perfect tool for non-designers and children to create in 3D.

App Info Launch App

Print through a distributed network of 3D printing enthusiasts from across the US, at a fraction of the cost of the competitors. We want to change the world for the better through technology, an...

App Info Launch App

Quickly Scale, Mirror or Cut your 3D Models

App Info Launch App

Treatstock is an online platform that offers decentralized manufacturing services such as 3D printing and CNC machining for business-to-business and business-to-consumer sales all over the world. W...

App Info Launch App

3D print your favourite design with NinjaPrototype, a professional 3D manufacture with consistent quality and speed.

App Info Launch App

which exact fan are you using? is it louder or quiter than then stock fan?

Could you please share the model or can you make a fan holders more fat (5mm each), cause this holders brakes quickly (very fragile)

I would suggest a modification to your design: rotating the 40mm fan mount 180°, so the fan sits higher and gives more clearance to the heating block. Probably this would also save you insulating the lower part with alumn foil from the heat.

How is the 5015 blower connected - is it wired in parallel with the 40mm heat block fan, thus running permanently? Or is there a special connector on the CR-10 board, which is able to turn on/off the 5015 blower fan while printing?

I wired cut the wire to the 4010 blower fan and place rc connectors on both the wires from the CR-10 and the 5015 fan. https://youtu.be/rfhc_C1oAQo?t=13m27s

On top is for a Radial Fan 5015 correct ?

Is the fang duct not touching the parts surface during print? because I had a similar attachment for the stock hotend and it was touching the surface. I had to cut a few mm so it will not touch the parts.

I am using this on my printer and everything works great. The fang does not touch the surface.

This is awesome, but I am going to have to hold out for an EZABL remix of this. Are you or anyone else willing to do the handiwork? It would be greatly appreciated. Thanks!

Is there any chance you can make a version of this for the e3d volcano? The nozzle tip is 8.5 mm lower than the standard V6.

How does this mount? What X-Carriage is recommended? For a Hictop (i3 Prusa).

I'm not sure a mount has been created for this model for that particular printer. This one is mostly used for the Creality series. A mount can be created for the Hictop but I don't see any as of right now that will work.

Just an FYI, I printed mine in PLA. When I started printing ABS in an enclosure, it melted and fell off. (Of course, I should have known PLA in enclosure, DUH--I'm really new at this lol)

But it's the perfect fan mount for me--I was in the middle of printing an ABS version anyway and now it's solid. A SilentX 40mm fan is so much quieter than the stock E3D fan. :)


I'm glad to see that you like the design. Thank you for the heads up about PLA I was just going to test mine with PLA.

Anyway you could add a bl touch mount like some of the other fangs have? for example the one in this?


Radial Fan Fang
by Lion4H

I'll look into it. It might be a few days I am in the process of upgrading my desktop hardware. Which my Fusion 360 is installed on.

Fully understand :)

Do you happen to have the step file or however you made it?

I uploaded the .step file.

How do you mount it to the machine

What I am using is a model from Bandanam4n: https://www.thingiverse.com/thing:2182924 But this attachment is for the Creality CR-10

E3D V6 mount for Creality CR-10

Any chance you could remix with the standard tarantula 30mm fan also? I've got the tevo volcano ready to go, but only the stock fan lol

Unfortunately, I don't have the right parts to do an accurate design and test. I wouldn't want to give you a design that may not work.

No worries :) I did find a 40mm to 30mm fan adapter that I can print, so tomorrow I'll try to remix and see if I can incorporate the 30mm fan, so I won't need the adapter lol. I'm super anxious to get this e3d running!

Is there the other part in the files ? The bit that fits onto the printer carriage ?

What I am using is a model from Bandanam4n: https://www.thingiverse.com/thing:2182924 But this attachment is for the Creality CR-10

E3D V6 mount for Creality CR-10
Comments deleted.