Loading

CR-10 BLTouch mount

by shocksofmighty, published

CR-10 BLTouch mount by shocksofmighty Aug 21, 2017
2 Share
Download All Files

Thing Apps Enabled

Order This Printed View All Apps

Contents

Tags

License

Liked By

View All

Give a Shout Out

If you print this Thing and display it in public proudly give attribution by printing and displaying this tag.

Print Thing Tag

Makes

Thing Statistics

5429Views 561Downloads Found in 3D Printing

Summary

A simple mount for BLTouch (Smart) for the stock CR-10 setup. I've reclaimed pin 31 from the SD card to use for servo control.

More from 3D Printing

view more

All Apps

Auto-magically prepare your 3D models for 3D printing. A cloud based 3D models Preparing and Healing solution for 3D Printing, MakePrintable provides features for model repairing, wall thickness...

App Info Launch App

With 3D Slash, you can edit 3d models like a stonecutter. A unique interface: as fun as a building game! The perfect tool for non-designers and children to create in 3D.

App Info Launch App

Print through a distributed network of 3D printing enthusiasts from across the US, at a fraction of the cost of the competitors. We want to change the world for the better through technology, an...

App Info Launch App

3D Print a wide range of designs with Treatstock. Easy to use tools to get the perfect result. The global 3D printing network that connects you with high-quality and fast working print services nea...

App Info Launch App

Short video made to configure marlin 1.1.8 on CR10S

https://www.youtube.com/watch?v=ENSyAQLpfpQ&t=3s

Attention if you want to use this change and keep the original switch z do not connect the WHITE AND BLACK cables

hello

where is the configuration in marlin for a home Z in the middle of the bed

thank you

Look for z_safe_home.

thank you very much I still have a problem heating errors happen at 52 ° of the bed

Hi all 3d printer !
Updated my CR-10S S5 to Bltouch and Keenovo Silicone Heater CR-10S S5.
https://www.youtube.com/watch?v=bp79Ks9agYk&feature=youtu.be
Thermal camera picture over Keenovo bed in zip file.
Bltouch, Wow, 0.001 ~ 0.05mm and works well with Ac bed.
In Bltouch CR-10S S5 Wiring, firmware mm.zip are everything you need if you want to try, except one Bltouch ;-)
Works very good.

In Marlin setup for bltouch, bedsize mm,zip
If you want to try !

Here are the most important changes in Marlin firmware Configuration.h you can do, needed for bltouch as well as set the size of your bed you have. There is much more to focus on but a good start that works, Bjax

I need massive assistance with this. All is installed and flashed and working... however my offset is off and no matter what I do to measure and set it correctly it just will not set for the middle of the bed. You have yours as 1.25 and I am curious how you got that number. I am at the point of exactly .1 of an offset and it prints decent. I have tried a few different numbers for the offset and some work and some don't, my issue arises when run a bed leveling... the middle is always pushing down in the middle of the bed and the outer edge is damn near perfect. What am I missing and perhaps what could I change? Thanks in advance.

Some values are saved in your printer's eeprom and are not changed when you flash a new firmware. You must reset your eprom if you change offset in configuration.h

Check this Z offset link.
https://www.youtube.com/watch?v=OoWP5C8lSig

On your LCD display under control, motion, you can set your Z offset as calculated via the linked movie. Remember to save the change. It is also very easy to increase or decrease if necessary.

May be difficult from the beginning to get good value and for me I had to have 6 clamps on the glass bed, if I have 4 st center too low.

Hope this helped a bit, Bjax

Thanks guys! Got mine going yesterday and it made a hell of a difference.

Glad to hear, I have just installed an E3D Aero to improve even more. Recommended! It's starting to be a really good printer.

Comments deleted.

Thanks Bjax. This is great information. I'm going to give it a try this weekend!

Thanks !
To me it works really well.
If you encounter problems, maybe I can help.
Good luck !

did you design this is f360? if so can you post the fusion file so i can modify this to work with a fang? Thanks!

Nope. It was done in Blender (and not very well, I might add)

Thanks for the post, would you have your offsets for this mount for marlin? I'm printing this currently and would like to have a starting point for tuning.

It depends mostly how you set it up (with or without the springs, etc.). You can probably start with 0.0 mm or -1.0 mm offset and work from there.

Can you point me to any instructions on how to configure the firmware and where to connect it?
Thanks

BLTouch on the stock board is not easy to do. Setting up the firmware just requires enabling BLTouch and setting the right pin. If you want to see how to use Pin 31 (removes SD card) you can see here: https://www.youtube.com/watch?v=ioL-7oEBI1Q&t=778s

Top