X-107 Micro Brushless Racing & Freestyle FPV Quadcopter Drone
Tips & Design Appreciation:
If you enjoy using my designs I would really appreciate it of you could please kindly take a minute to show your appreciation with a small "tip". Your contributions can assist in filament and parts purchases that can help me to design and make better multi-rotors frames.
So if you can show your appreciation with a tip or a share, it would be fantastic as you would support me and the aims above. If not, no worries!
I just hope that you have a fantastic time using the X-107 frame kit to build your own FPV Freestyle & Racing Micro Quadcopter Drone!
Social, Media & Sharing:
If you are proud of your creation please do take a picture of your build and share it with a the link for this page online so that others can also find out and enjoy using the design also.
To me personally it is very satisfying to see someone take the time to use my work and I would love to see what you make!
You can join the below Facebook groups where you can meet other people interested printing and FPV:
If you would like to see some footage of my designs in actions you can check out my Youtube page:
I list my designs here on Thingiverse for free so that others can enjoy a reduction in the cost of the hobby and so they can have something fun and unique to fly.
3D Printing and drone building and flying can provide fun avenue to learn about mathematics, science and technology and can also help people find a sense of community. Part of providing free access is to help the young and those in education by providing a tool that can be utilized cheaply and easily. Creativity is a great tool for well-being and I also hope that by providing people a cheap route to a fun hobby they can enhance their lives.
- True X 107 mm Unibody With Vertical Arms.
- 19 X 19 camera compatible.
- 20 X 20 mm & 16 X 16 mm stacks.
- 11xx motors up to 9 mm mount in M2 Hardware.
- 2" propellers.
- Support free printing.
- New active geometry formula applied.
There are four body options available. They are identical save for the hardware sizes that they accommodate to mount the flight stack, namely M2 & M3. The frames designated "Drop Mount" have a recesses in the frame at each of the stack mount points to allow use of shorter bolts.
The Top Plate has 2 options in M2 and M3 hardware so that you can mount components or accessories of your choice easily and also design the same to fit the standard mount sizing. Both the Top Plates accept M3 hardware to mount to the Body.
To build choose a Body that is right for your hardware and also a Top Plate. Print them, screw your hardware to them.
YOU MUST USE MORE THAN 2 BOLTS TO SECURE YOUR MOTORS IF THEY ALLOW!
The entire frame kit should be printable in all common filament materials such as PLA, PETG, ABS & NYLON. I use an infill at 15% with the "Tri-Hex" pattern to maximize strength. This is a good starting point, but feel free to experiment and see what works best for your setup.
The frame may be viable in flexiable filament, but this has not been tested.
To print, lay the pieces down on the bed flat so that largest flat side is on the bed.
Printed frames are not carbon frames, it’s easy to forget that when you are flying. It is advised to treat a printed frame like that of a Tiny Whoop and to avoid landing on the motor bottoms or corners of the arms.
When you first get it into the air, treat it gently until you get used to it. Since there frames are designed to balance perfectly and are actually “true X” this may feel a little strange at first. You may note that your sticks will be more even across all the axis of movement.
It is recommended to bottom mount the battery for the longevity of the frame and arms. Of course, once you are proficient and comfortable flying with the frame mount as you wish.
Plastic frames will protect your components very well, particularly from current and voltage spikes that normally kill components during crashes. Secondarily the frame breaking during an impact absorbs a great deal energy which would otherwise damage your components. The frames are designed to fully enclose the key components as much as possible of the drone so you should hopefully enjoy parts that last for a long time.
ALWAYS CHECK FLYING REGULATIONS AND RESTRICTIONS LOCAL TO YOU BEFORE ATTEMPTING TO FLY YOUR CRAFT.
Originality of Design
Of key importance to me is that my designs are original works. I always make my designs from scratch and try and make them as distinct as possible.
I have taken great care make sure that my design does not take directly from anyone else’s work or infringes on any copyrights or patents.
The unique geometry of this design alongside its unique design features identifies it as an original design and also builds in copy protection. If there is any duplication of any part of this design, a measurement can be taken of any two points and by simple calculation it can be proved.
I am a British citizen and this design was produced in the United Kingdom. The natural design rights reside with me as accorded by European Union law.
In no event shall I the designer be liable for any direct, indirect, punitive, incidental, special consequential damages, to property or life, whatsoever arising out of or connected with the use or misuse of any of my designs.
In using my work you acknowledge that any and all liability is with you the user.
You use this design at your own risk and are responsible for any consequences as such.