Note! This project is slowly migrating to Github. STLs, instructions, and other files will slowly be removed here and placed on Github for the long term.
Welcome to the Jubilee project, my take on an open-source multi-tool motion platform with a rock-solid toolchanging system. My hope is that, with toolchanging becoming a more common solution, we enable a community-driven ecosystem of tools for a variety of applications from fabrication, to art, to scientific instrumentation.
Jubilee isn't just a 3D printer with many heads; it's a piece of infrastructure. For the 3D printer enthusiast, it is a rock-solid monochrome and multicolor 3D printer. For the budding machine designer, it's a reference design using classic machine-design principles. For the scientist, artist, and everyone else, Jubilee is your application platform; it can be extended to accommodate a range of custom applications.
Jubilee's toolchanging system uses a torque-based locking system. As a result, it's able to consistently pick up toolplates with small geometry variations in the groove disc. This design tweak enables you to print tool plates from a variety of printers, and they will all lock consistently throughout the lifespan of the groove disc. Furthermore, with a special thanks to E3D, Jubilee's carriage is hardware compatible with E3D tool plates. Perhaps, someday, you will be able to buy them directly from E3D.
Finally, Jubilee's build plate is also kinematically-coupled, making it hot-swappable without losing its position. With this feature parts can be stopped-and-modified mid-process or loaded onto a different machine altogether to undergo a separate process. As a result, Jubilee can be leveraged for truly cross-platform applications that are especially useful to scientific instrumentation and mixed additive-and-subtractive manufacturing.
Building on contributions from E3D, I would like to invite us to standardize our printer-based toolchanging systems. We live in an exciting time where we're just beginning to taste the glory of truly multitool motion platforms. However, as we separately develop our own solutions for toolchanging, we segregate our victories. Toolchanging becomes a victory for a few lone builders with unique, isolated solutions.
Jubilee is my attempt to bring toolchanging to the entire 3D printer community with a common standard. Jubilee isn't just my victory; it's yours! And with a carriage system compatible with E3D plates, we can create an ecosystem of platforms which all have a common set of interchangeable tools. With a common tool standard, we could step into a world where we design-and-share novel tools, not toolchangers.
In the future, I would love to try building your syringe heads, plotter heads, pancake-extruding heads--you name it! But to do so, we need to settle on a common tool interface, an API in hardware. For that reason, I designed Jubilee with the hope that it can be replicated. In the spirit of RepRap, Jubilee maximizes its use of 3D-printed parts, leveraging them where they work best. And while it is not exactly self-replicating, it is fabricatable, something you can build yourself without specialized tools or machine-design expertise.
- Designed with Exact-Constraint machine-design principles
- Automatic Toolchanging System compatible with E3D tool plates
- Perfectly-Constrained hot-swappable bed plate
- autotramming with 3-point bed-leveling (courtesy of the Duet)
- 300x300x190mm build space. Designed such that the Z-axis can be adjusted to your liking.
- Core-XY layout for high-speed printing. Rapids of 25000 mm/min and higher with tuning.
- Flush-Form CoreXY Belt Pattern. Upper and lower belts are laid out directly on top of each other, and belts only travel perpendicular to the frame. Belt-tensioning is done conveniently with two set-screws that adjust the motor locations along slots.
- Stellar print quality with direct-drive extruders. Jubilee can compete with systems at the $5K price range.
- User Extensible! Jubilee can accommodate custom tools and custom bed plates for specialized 3D-printing and uses beyond 3D printing. (See the Extending section)
- Cycle-tested. Jubilee has performed thousands of toolchanges flawlessly.
- Completely Open-Source with a CC-BY license. Make use of the Jubilee design in ways that suit you. (STLs, STEPs, and original Solidworks assemblies are included.)
- Documented with a comprehensive BOM and set of assembly instructions.
- Almost all fabricated parts are 3D printable. Printed parts are intentionally kept simple and minimize the use of support material. (Exceptions: the bed plate, crossbar, and toolchanger lock must be machined. See notes in the BOM for getting these parts made for cheap.)
- Metric fasteners everywhere.
Jubilee runs on the Duet Ethernet with the Duex5 expansion board. You can download the config files to get you up-and-running here
Jubilee interprets Marlin-Style GCode. Any Slicer that can export Marlin-style gcode should be compatible. All toolchange-related state information is handled at the board level (via macro files). At the slicer level, you need only run T0, T1, etc. to execute a tool change; the firmware handles the complexity of parking the current tool, picking up the next tool, and adjusting XYZ offsets.
Quickstart for Making your Own Jubilee
- Budget $1600 for the frame and ~$200 per extruder. Then order all parts in the Shopping list
- Gather all assembly tools in the [tools list]()
- Setup an ethernet connection to Jubilee via the setup page [here]()
- Upload all config files from the repository to the Duet SD card
- Build the frame and your desired number of extruder tools
- Adjust the parking post positions for toolchanges
- Run a bed temperature calibration and extruder heater calibration for each tool
- Dial in the XYZ offsets for each tool. (See below)
- Load some filament and celebrate!
For reference, all parts were printed on my Prusa Mk3. Here are my suggested settings.
- print all parts in the provided orientations
- 0.2mm layer height
- 6 perimeter layers (This is especially critical for parts that have heat-set inserts)
- 2-3mm brim suggested, but not required
- no supports except left_corner_plate.STL and right_corner_plate.STL
Note: Parts cannot be used if they peel off the print bed. They must come out flat.
Print 1 of everything except,
- 4x printed pulley spacer
- 2x belt clasp
- 2x parking post top
- 2x parking post bottom
All laser-cut parts are made from either Acrylic or Acetal (Delrin). While some parts can be replaced with 3D-printed versions, I can't guarantee that they will work as well.
Notes on Assembly
Jubilee takes about 8-12 hours to assemble the frame. (Snag yourself a gummy-bear pack to get you through it!) However, some sets of instructions can actually assembled in parallel unless they specifically call for parts in prior instructions. With that said, get some friends or family in the same room to tackle this build.
Parking posts are adjustable in the vertical (Z) and horzontal (X) directions through adjustable screw points. When it comes to tuning tool locations, rather than change your config files to match your hardware, I suggest changing your hardware to match the config locations. I suggest this route because the parking location actually needs to be changed in multiple files, tfree.g, and tpre.g and possibly even in your Slicer scripts if you adding any special wipe routines besides simply invoking T0, T1, etc. In this way, I can continue to push out releases and your config files, by and large, will remain mostly the same.
Jubilee can do much more than multitool 3D printing. Best of all, you need not be a machine-design expert to do so!
Jubilee can be extended for custom applications beyond 3D printing. See the upcoming extension notes to get relevant dimensions for your own build plate.
If you make a custom Jubilee head, why not tag it with jubilee_head so that others can find it?
Jubilee can be used for multitool 2-axis applications, such as multicolor plotting or lightweight lab-automation and inspection. To do so, simply build the xy frame. (Stay tuned for config-files specific for plotter builds.)
Adjusting Parking Post Locations
To be written!
Dialing in XYZ offsets
To be written!
Q: Can I just cut my own extrusions, instead of buying them from Misumi?
A: Yes, but it is almost certainly more trouble than it's worth. Misumi does a fantastic job getting square cuts within 0.1mm of the correct length. The building instructions assume that the frame cuts are the same length such that the machine can be squared properly. If you make these parts yourself, you'll need to get same-length extrusions to be as-close-as-possible to the same length in real life. (In practice, this is quite difficult without a milling machine or cold saw.)
Feel free to DM me if you find mistakes or if you use Jubilee to do something awesome. I would love to hear about how you are using Jubilee for art, science, and other mischief.
If you're building your own Jubilee, why not join the Discord Channel?
While the frame and toolchanging system is feature-complete, Jubilee is a work-in-progress. Be sure to check the updates list at the bottom to see if anything new happened. In the meantime, here are some changes coming down the road.
- BOM update. (The current BOM is missing some miscellaneous items for cable management and optional connectors.)
- Stay tuned for the Twist Lock component to go up on sale on Tindie.
- Instructions update. The instructions are usable but still in draft form. Feedback via DM is most welcome.
- Jubilee Head Assembly Instructions.
- Jubilee currently prints with a wipe tower. With a proper nozzle wiping system, it should print without this sacrificial piece. Preliminary wiping looks promising, although it is not yet released, but that's where you, the community, could help!
- Head Wiring Management Instructions
- Wiring Diagram of the whole system
- Build videos
I have found so much joy in discovering new engineering tricks from the open-source community that I grew up with. Sharing my jubilee through Jubilee is one way that I can give back. Here's a quick (but still incomplete list of people to thank)
- Dr. Nadya Peek of the Machine Agency Lab
- Fellow Machine Agents Hannah (who took the spectacular front-page photo) and Jasper
- J Steve White and Tony Atkens of the Railcore project
- Sanjay Mortimer and the E3D Design team behind their Toolchanging Motion System
- The folks at 713maker.com, who now offer Jubilee parts.
- James Best, Amy Qian, Chris Cotner, Andrey Shur, Brandon Whitney, Eric Moyer, and many other fellow machine-and-mechanism builders of past and present
- My Hackaday writing crew
- Matt Keeter, for showing me the value of well-documented infrastructure
- Sept 9, 2019 Initial Release
- Sept 14, 2019 (1) SW-2019 Files updated into a Hierarchical Assembly, (2) added countersink feature added to bed plate coupling screws for added generalizability across user community, (3) adjusted compact leadscrew retainer shape.
- Sept 27, 2019 Added Z axis assembly instructions draft and updated XY Assembly instructions.
- Oct 5, 2019 Updated Z axis assembly to add extruder ooze wiper assembly instructions. Updated CAD model to include Ooze wipers.